t18xsd1eq Banner Engineering Corp., t18xsd1eq Datasheet
t18xsd1eq
Related parts for t18xsd1eq
t18xsd1eq Summary of contents
Page 1
Printed in USA EZ-BEAM ® T18XSD Smart Sensors “Intelligent” Photoelectric Sensors for use on SDS • Low cost and easy to use; no adjustments are necessary • Models available for opposed (through-beam), retroreflective, polarized retroreflective, diffuse and fixed-field modes • ...
Page 2
... T18XSD Series Models Range Cable T18XSD1EQ 20 m 4-pin Euro QD (66') T18XSD1RQ Models Range Cable Polarized 2 m 4-pin Euro QD T18XSD1LPQ (79") Non-Polarized 2 m 4-pin Euro QD T18XSD1LQ (79") 2 page Opposed Mode Emitter (E) and Receiver (R) Supply Voltage Excess Gain 1000 100 11-25V dc ...
Page 3
... Euro QD T18XSD1FF50Q (2") 100 mm far limit cutoff 100 mm 4-pin Euro QD T18XSD1FF100Q (4") Banner Engineering Corp. • Minneapolis, U.S.A. Website: http://www.baneng.com • Tel: 888.373.6767 Diffuse Mode Excess Gain Supply Voltage Performance based on 90% reflectance white test card 1000 T18XSD Series ...
Page 4
... Jam Nut (Supplied) M18 x 1 Thread ø 40.0 mm (1.57") ø 66.5 mm (2.62") ® (opposed models) or acrylic (retro and fixed-field T18XSD Emitter ø 30.0 mm 30.0 mm (1.18") (1.18") (0.59") Green LED Power"dicator 11.5 mm (0.45") Banner Engineering Corp. • Minneapolis, U.S.A. Website: http://www.baneng.com • Tel: 888.373.6767 56.6 mm (2.23") ...
Page 5
... Drill screw holes 24.2 mm (0.95") apart (1.2") (1.60" (0.95") (1.80") 4.6 mm (0.18")* ø 4.6 mm 7.6 mm (0.18")* (0.30") Banner Engineering Corp. • Minneapolis, U.S.A. Website: http://www.baneng.com • Tel: 888.373.6767 Hookups Mounting Brackets SMB18C 42.4 mm (1.67") 14.0 mm (0.55") SMB18S 25.4 mm (1.00") 44.5 mm (1.75" (0.40") 13.0 mm (0.50") ...
Page 6
... Byte 1 125 XXXXX - X.X Byte 1 Byte 2 Byte 1 0 Long 1 XX...X 4 MMYY 24 T18XSD1XXX (Model number) 24 “Banner Engineering” 24 “Photoelectric Sensor” Byte Blank Byte Byte 1 0 Banner Engineering Corp. • Minneapolis, U.S.A. Website: http://www.baneng.com • Tel: 888.373.6767 ...
Page 7
... Diagnostic Error Counter 9 Bus Diagnostics Register 10 Cyclical Timer Banner Engineering Corp. • Minneapolis, U.S.A. Website: http://www.baneng.com • Tel: 888.373.6767 Attributes 18,1,0,0,0,0 These six bytes indicate that this is a single point binary input with the input variable at Attribute #18. Always returns 0. This indicates that this device automatically determines the correct baud rate for communication ...
Page 8
... Disable re-transmission of COS messages R/W. When this bit is set ALL event driven messages are sent only once per event. Unacknowledged messages are not resent. bits Not used. This attribute is stored in non-volatile memory. Action Banner Engineering Corp. • Minneapolis, U.S.A. Website: http://www.baneng.com • Tel: 888.373.6767 ...
Page 9
... Reset Errors 8 Enroll Force Input/Output Variable 51 State Remove Force Input/Output 52 Variable State 53 Read Primitive Tag Banner Engineering Corp. • Minneapolis, U.S.A. Website: http://www.baneng.com • Tel: 888.373.6767 Actions Requested Data Requested Data Type None New Address Unsigned 8 Device ID* Unsigned 8 Device ID* Unsigned 16 Serial No.* ...
Page 10
... When the output of the sensor transitions to the ON state, this message is sent. This event can be masked by clearing attribute 6. When the output of the sensor transitions to the OFF state this message is sent. This event can be masked by clearing attribute 6. Output Data Parameter Type Unsigned 8 Action Banner Engineering Corp. • Minneapolis, U.S.A. Website: http://www.baneng.com • Tel: 888.373.6767 ...
Page 11
... Banner Engineering Corp. • Minneapolis, U.S.A. Website: http://www.baneng.com • Tel: 888.373.6767 T18XSD Series 11 page ...
Page 12
... T18XSD Series WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. ...