ltc3850gn-2 Linear Technology Corporation, ltc3850gn-2 Datasheet - Page 13

• Manufacturer Part Number: ltc3850gn-2
• Description: Dual, 2-phase Synchronous Step-down Switching Controller
• Manufacturer: Linear Technology Corporation

APPLICATIONS INFORMATION
sets the peak of the inductor current, yielding a maximum
average output current I
half the peak-to-peak ripple current, ΔI
sense resistor value, use the equation:
Because of possible PCB noise in the current sensing loop,
the AC current sensing ripple of ΔV
also needs to be checked in the design to get a good
signal-to-noise ratio. In general, for a reasonably good
PCB layout, a 15mV ΔV
a conservative number to start with, either for R
DCR sensing applications.
For previous generation current mode controllers, the
maximum sense voltage was high enough (e.g., 75mV for
the LTC1628 / LTC3728 family) that the voltage drop across
the parasitic inductance of the sense resistor represented
a relatively small error. For today’s highest current density
solutions, however, the value of the sense resistor can
be less than 1mΩ and the peak sense voltage can be as
low as 20mV. In addition, inductor ripple currents greater
than 50% with operation up to 1MHz are becoming more
common. Under these conditions the voltage drop across
the sense resistor’s parasitic inductance is no longer neg-
ligible. A typical sensing circuit using a discrete resistor is
shown in Figure 2a. In previous generations of controllers,
a small RC fi lter placed near the IC was commonly used to
reduce the effects of capacitive and inductive noise coupled
inthe sense traces on the PCB. A typical fi lter consists of
two series 10Ω resistors connected to a parallel 1000pF
capacitor, resulting in a time constant of 20ns.
This same RC fi lter, with minor modifi cations, can be used to
extract the resistive component of the current sense signal
in the presence of parasitic inductance. For example, Figure
3 illustrates the voltage waveform across a 2mΩ sense
resistor with a 2010 footprint for the 1.2V/15A converter
shown in Figure 18 operating at 100% load. The waveform
is the superposition of a purely resistive component and a
R
SENSE
=
I
V
(MAX)
SENSE(MAX)
+
ΔI
2
SENSE
L
MAX
equal to the peak value less
voltage is recommended as
SENSE
L
. To calculate the
= ΔI
L
• R
SENSE
SENSE
or
purely inductive component. It was measured using two
scope probes and waveform math to obtain a differential
measurement. Based on additional measurements of the
inductor ripple current and the on-time and off-time of
the top switch, the value of the parasitic inductance was
determined to be 0.5nH using the equation:
If the RC time constant is chosen to be close to the parasitic
inductance divided by the sense resistor (L/R), the result-
ing waveform looks resistive again, as shown in Figure
4. For applications using low maximum sense voltages,
check the sense resistor manufacturer’s data sheet for
information about parasitic inductance. In the absence of
data, measure the voltage drop directly across the sense
resistor to extract the magnitude of the ESL step and use
the equation above to determine the ESL. However, do not
over-fi lter. Keep the RC time constant less than or equal
to the inductor time constant to maintain a high enough
ripple voltage on V
The above generally applies to high density / high current
applications where I
are used. For applications where I
and C
The fi lter components need to be placed close to the IC. The
positive and negative sense traces need to be routed as a
differential pair and Kelvin connected to the sense resistor.
Inductor DCR Sensing
For applications requiring the highest possible effi ciency at
high load currents, the LTC3850-2 is capable of sensing the
voltage drop across the inductor DCR, as shown in Figure
2b. The DCR of the inductor represents the small amount
of DC winding resistance of the copper, which can be less
than 1mΩ for today’s low value, high current inductors.
In a high current application requiring such an inductor,
conduction loss through a sense resistor would cost several
points of effi ciency compared to DCR sensing.
ESL
F
to 1000pF . This will provide a good starting point.
=
V
ESL STEP
Δ
(
I
L
RSENSE
(MAX)
)
t
t
ON
ON
> 10A and low values of inductors
+
•
.
t
t
OFF
OFF
(MAX)
LTC3850-2
< 10A, set R
F
13
to 10Ω
38502f