lan9118 Standard Microsystems Corp., lan9118 Datasheet - Page 98

no-image

lan9118

Manufacturer Part Number
lan9118
Description
Lan9118 High-performance Single-chip 10/100 Non-pci Ethernet Controller
Manufacturer
Standard Microsystems Corp.
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
lan9118-MT
Manufacturer:
SMSC
Quantity:
6
Part Number:
lan9118-MT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
lan9118-MT
Manufacturer:
SMSC
Quantity:
8 000
Part Number:
lan9118-MT
Manufacturer:
SMSC
Quantity:
20 000
Company:
Part Number:
lan9118-MT
Quantity:
106
Part Number:
lan9118-MT-E2
Manufacturer:
INTEL
Quantity:
18
Part Number:
lan9118-MT-E2
Manufacturer:
SMSC
Quantity:
20 000
Part Number:
lan9118MT
Manufacturer:
Standard
Quantity:
5 057
Part Number:
lan9118MTC-MT
Manufacturer:
SMSC
Quantity:
1 000
Revision 1.5 (07-11-08)
5.4.3
BITS
31-0
EEPROM ADDRESS
Physical Address [31:0]. This field contains the lower 32 bits (31:0) of the Physical Address of the
LAN9118 device. The content of this field is undefined until loaded from the EEPROM at power-on.
The host can update the contents of this field after the initialization process has completed.
ADDRL—MAC Address Low Register
The MAC Address Low register contains the lower 32 bits of the physical address of the MAC. The
contents of this register are optionally loaded from the EEPROM at power-on through the EEPROM
Controller if a programmed EEPROM is detected. The least significant byte of this register (bits [7:0])
is loaded from address 0x01 of the EEPROM. The most significant byte of this register is loaded from
address 0x04 of the EEPROM. Please refer to
Table 5.7
reception of the Ethernet physical address. Also shown is the correlation between the EEPROM
addresses and ADDRL and ADDRH registers.
As an example, if the desired Ethernet physical address is 12-34-56-78-9A-BC, the ADDRL and
ADDRH registers would be programmed as shown in
load this configuration from the EEPROM are also shown.
Note: By convention, the left most byte of the Ethernet address (in this example 0x12) is the most
0x01
0x02
0x03
0x04
0x05
0x06
Offset:
Default Value:
significant byte and is transmitted/received first.
below illustrates the byte ordering of the ADDRL and ADDRH registers with respect to the
Figure 5.2 Example ADDRL, ADDRH and EEPROM Setup
Table 5.7 ADDRL, ADDRH and EEPROM Byte Ordering
31
31
0x78
xx
24
24
23
23
0x56
xx
ADDRH
ADDRL
16
16
3
FFFFFFFFh
15
15
ADDRL[23:16]
ADDRL[31:24]
ADDRH[15:8]
ADDRL[15:8]
DATASHEET
ADDRH[7:0]
ADDRL[7:0]
0xBC
0x34
ADDRN
8
8
DESCRIPTION
98
7
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
7
0x9A
0x12
Section 4.6
0
Attribute:
Size:
0
Figure
for more information on the EEPROM.
5.2. The values required to automatically
0x06
0x05
0x04
0x03
0x02
0x01
0x00
ORDER OF RECEPTION ON
EEPROM
R/W
32 bits
0xBC
0x9A
0xA5
0x78
0x56
0x34
0x12
ETHERNET
2
3
1
4
5
6
nd
rd
th
th
th
st
SMSC LAN9118
Datasheet

Related parts for lan9118