mn101ca3 Panasonic Corporation of North America, mn101ca3 Datasheet

no-image

mn101ca3

Manufacturer Part Number
mn101ca3
Description
Mn101ca3 Series
Manufacturer
Panasonic Corporation of North America
Datasheet
 Interrupts
 Timer Counter
 Serial interface
 DMA controller
 I/O Pins
 A/D converter
 Display control function
Type
Internal ROM type
ROM (byte)
RAM (byte)
Package (Lead-free)
Minimum Instruction
Execution Time
RESET. Watchdog. External 0 to 6. Timer 0 to 4. Timer 6. Timer 7 (2 systems). Timer 8 (2 systems). Time base. Serial 0 (2 systems).
Serial 1 (2 systems). Serial 2. Serial 3 (2 systems). A/D conversion finish. Automatic transfer finish. FL display key scan. FL display
dimmer
8-bit timer × 6
16-bit timer × 2
Time base timer: One-minute count setting
Watchdog timer × 1
Synchronous type/UART (full-duplex) × 2: Serial 0, 1
Synchronous type/Single-master I
UART (full-duplex) × 1: Serial 3
Maximum transfer cycles: 255
Starting factor: External request. Various types of interrupt. Software
Transfer mode: 1-byte transfer. Word transfer. Burst transfer
I/O
High Voltage
8-bit × 8 channels (with S/H)
FL: (35 to 43) segments × (18 to 10) digits
16 levels dimmer function
Light-and-dark 2-tones display function
Can support automatic display to universal grid display tubes
Output dimmer waveform for FL driver connection (DROUT)
Internal pull down resister is available between Port 6 and Vpp, Port 9 and Vpp, Port B and Vpp, Port C and Vpp, Port D and Vpp by
Mask option (only for Mask ROM version)
Internal pull down resister between Port 4 and Vpp, Port 7 and Vpp, Port 8 and Vpp
MN101CA3 Series
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output. Simple pulse width measurement
Timer 1 ..................Square-wave output. Event count. Serial transfer clock output
Timer 2, 4 ..............Square-wave/8-bit PWM output. Serial transfer clock output. Event count. Simple pulse width measurement
Timer 3 ..................Square-wave output. Event count. Remote control carrier output. Serial transfer clock output
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
Timer 7, 8 ..............Square-wave output. 16-bit PWM output (cycle/duty continuous variable). Event count. Pulse width measurement.
36 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
53 : Output: 26. I/O: 27. P-ch. open drain (breakdown voltage –40 V): FL drive: 53. Specified pull-down resistor mask
option: 35
Input capture
2
C × 1: Serial 2
*: The lower limit for operation guarantee for flash memory built-in type is 2.5 V.
MN101CA3F
Mask ROM
96K
4K
0.48 µs (at 2.3 V to 5.5 V, 4.19 MHz)*
0.24 µs (at 2.7 V to 5.5 V, 8.4 MHz)
1.0 µs (at 2.0 V to 5.5 V, 2.0 MHz)*
62.5 µs (at 2.0 V to 5.5 V, 32 kHz)*
0.1 µs (at 4.5 V to 5.5 V, 20 MHz)
QFP100-P-1818B
MN101CFA3G
FLASH
128K
10K
MAD00068DEM

Related parts for mn101ca3

mn101ca3 Summary of contents

Page 1

... MN101CA3 Series Type Internal ROM type ROM (byte) RAM (byte) Package (Lead-free) Minimum Instruction Execution Time  Interrupts RESET. Watchdog. External Timer Timer 6. Timer 7 (2 systems). Timer 8 (2 systems). Time base. Serial 0 (2 systems). Serial 1 (2 systems). Serial 2. Serial 3 (2 systems). A/D conversion finish. Automatic transfer finish. FL display key scan. FL display dimmer  ...

Page 2

... P52, LED2, SBT0B 93 P10, TM0IO, RMOUT 94 P11, TM1IO 95 P12, TM2IO 96 P13, TM3IO 97 P14, TM4IO 98 P15, TM7IO 99 P16, DROUT, SSTART 100 MAD00068DEM MN101CA3F, MN101CFA3G 50 DGT4, SEG3, P74 49 DGT5, SEG2, P75 48 DGT6, SEG1, P76 47 DGT7, SEG0, P77 46 DGT8, P40 45 DGT9, P41 44 DGT10, P60 43 DGT11, P61 ...

Page 3

Request for your special attention and precautions in using the technical information and (1) If any of the products or technical information described in this book exported or provided to non-residents, the laws and regulations of the ...

Related keywords