Interrupts
Timer Counter
Serial interface
DMA controller
I/O Pins
A/D converter
Display control function
Type
Internal ROM type
ROM (byte)
RAM (byte)
Package (Lead-free)
Minimum Instruction
Execution Time
5 external interrupts. 29 internal interrupts
RESET. NMI. External 0 to 4. Timer 0 to 4. Timer 6. Timer 7 (2 systems). Timer 8 (2 systems). Timer 9 (3 systems). Time base. 24H
timer. Alarm. Serial 0 (2 systems). Serial 1 (2 systems). Serial 2 (2 systems). Serial 4 (2 systems). LIN. A/D conversion. ATC. Key
interrupt. Low voltage detection
8-bit timer × 7
16-bit timer × 3
24H timer: Interval function (Interruption every 0.5 seconds, every 1 second, every 1 minute, every 1 hour and 24 hours). Alarm function
Time base timer: One-minute count setting
Watchdog timer × 2
Synchronous type/UART (full-duplex)/LIN × 1: Serial 0
Synchronous type/UART (full-duplex) × 2: Serial 1, 2
Synchronous type/Multi-master I
1 systems. Maximum transfer cycles are 255
Starting factor: External request. Internal event. Software
I/O
10-bit × 12 channels
LCD: 32 segments × 4 commons (Static, 1/2, 1/3, or 1/4 duty)
Usable if VLC1 ≤ VDD
MN101E58 Series
Timer 0 ..................Timer pulse output. Added pulse(2-bit)type PWM output to large current terminal TM0IOB possible. Event count.
Timer 1 ..................Timer pulse output. Event count. 16-bit cascade connected (timer 0, 1). Timer synchronous output
Timer 2 ..................Timer pulse output. Added pulse(2-bit)type PWM output to large current terminal TM2IOB possible. Event count.
Timer 3 ..................Timer pulse output. Event count. 16-bit cascade connected (timer 2, 3). 32-bit cascade connected (timer 0, 1, 2, 3)
Timer 4 ..................Timer pulse output. Added pulse (2-bit) type PWM output. Event count. Simple pulse width measurement
Timer 6 ..................8-bit freerun timer
Timer A ..................Baud rate timer. Clock output for peripheral function
Timer 7 ..................Timer pulse output to large current terminal TM7IOB possible. Event count. High accuracy PWM/IGBT output
Timer 8 ..................Timer pulse output to large current terminal TM8IOB possible. Event count. High accuracy PWM output
Timer 9 ..................Timer pulse output to large current terminal TM9IOB possible. 3-phase PWM output. Triangular waveform
54 : Common use. Specified pull-up/pull-down resistor available. Input/output selectable (bit unit)
Simple pulse width measurement
Simple pulse width measurement. 24-bit cascade connected (timer 0, 1, 2). Timer synchronous output
(cycle/duty continuous variable). Pulse width measurement. Timer synchronous output. Input capture (both edge
available). Real time output control. Double buffer compare register
(cycle/duty continuous variable). Pulse width measurement. Input capture (both edge available). 32-bit cascade
connected (timer 7, 8). 32-bit PWM output. Synchronous output event. Double buffer compare register
output. Jigsaw waveform output. Dead time setup. Event count
2
C × 1: Serial 4
*: at internal 2 , 3 , 4 , 5 , 6 , 8 , 10 times oscillation used
LQFP064-P-1414, TQFP064-P-1010C
50 ns (at 2.7 V to 5.5 V, 20 MHz)
125 ns (at 1.8 V to 5.5 V, 8 MHz)
MN101EF58G
FLASH
128K
6K
MAD00081BEM