znbg3113 Zetex Semiconductors plc., znbg3113 Datasheet
znbg3113
Available stocks
Related parts for znbg3113
znbg3113 Summary of contents
Page 1
... QSOP surface mount package ZNBG3113 ZNBG3114 Drain current setting of the ZNBG3113/14 is user selectable over the range 0 to 15mA, this is achieved with addition of a single resistor. The series also offers the choice of drain voltage to be set for the FETs, the 3113 gives 2 ...
Page 2
... ZNBG3113 ZNBG3114 ABSOLUTE MAXIMUM RATINGS Supply Voltage -0.6V to 12V Supply Current 100mA Input Voltage (V ) 25V Continuous POL Drain Current (per FET 15mA (set CAL Operating Temperature -40 to 70°C Storage Temperature -50 to 85°C ELECTRICAL CHARACTERISTICS. TEST CONDITIONS (Unless otherwise stated):T amb ...
Page 3
... V D3 Voltage Change V with 10V with T T =-40 to +70° Leakage Current I Drain 1 V =0.1V Drain 2 V =0.1V ZNBG3113 ZNBG3114 MIN. - POL GOx ( =14 I =-10 -2.7 POL GO1 =15.5 I =-10 -2.7 POL GO1 =15 0.4 POL GO1 =15.5 I =-10 -2.7 POL ...
Page 4
... ZNBG3113 ZNBG3114 SYMBOLPARAMETER CONDITIONS TONE DETECTION CHARACTERISTICS Filter Amplifier I Input Bias Current R =150k Output Voltage R =150k OUT Output Current V =1.96V, V OUT OUT G Voltage Gain f=22kHz,V V Rectifier 5 V Output Voltage R =150k OUT Leakage Current R =150k LEAK F1 Comparator V Threshold ...
Page 5
... TEST CIRCUIT 1 TEST CIRCUIT 2 ZNBG3113 ZNBG3114 V2 Characteristics Type AC source Frequency 22kHz Voltage 350mV p/p enabled 100mV p/p disabled V2 Characteristics Type AC source Frequency 22kHz Voltage 350mV p/p enabled 100mV p/p disabled 4-127 ...
Page 6
... ZNBG3113 ZNBG3114 TYPICAL CHARACTERISTICS 16 Vcc = (k) cal JFET Drain Current v R cal 2.4 2.3 2.2 Vcc = 10V 2.1 2 Drain Current (mA) JFET Drain Voltage v Drain Current Note:- Operation with loads > 200µA is not guaranteed. 0.0 -0.5 -1.0 Vcc = ...
Page 7
... Frequency (Hz) Open Loop Phase v Frequency 1 1.2 V =0.1Vpkpk IN Test Circuit 1 1.0 0.8 0.6 0.4 0.2 0 100 1k 10k 100k Frequency (Hz) Filter Response ZNBG3113 ZNBG3114 10M Load Current (mA) LB/HB Offset Voltage v Load Current 2.0 1.9 1.8 1.7 1.6 1.5 1.4 1.3 1.2 10M Load Current (mA) ...
Page 8
... The ZNBG devices provide all the bias requirements for external FETs, including the generation of the negative supply required for gate biasing, from the single supply voltage.The diagram above shows a single stage from the ZNBG series. The ZNBG3113/14 contains 3 such stages. The negative rail generator is common to both devices. ...
Page 9
... FET number Q3 is always active regardless of the voltage applied POL Control Input Switch Function Input Sense Polarisation Select Vertical FET Q2 14 volts Horizontal FET Q1 15.5 volts ZNBG3113 ZNBG3114 input. Only one of the two external FETs POL 4-131 . POL ...
Page 10
... ZNBG3113 ZNBG3114 For many LNB applications tone detection and band switching is required. The ZNBG3113/14 includes the circuitry necessary to detect the presence of a 22kHz tone modulated on the supply input to the LNB. Referring to the following schematic diagram, the main elements of this detector are an op-amp enabling the construction of a Sallen Key filter, a rectifier/smoother and a comparator ...
Page 11
... Should the negative bias generator be shorted or overloaded so that the drain current of the external FETs can no longer be controlled, the drain supply to FETs is shut down to avoid damage to the FETs by excessive drain current. ZNBG3113 ZNBG3114 pin. SUB ...
Page 12
... The following block diagram shows the main section of an LNB designed for use with the Astra series of satellites. The ZNBG3113/14 is the core bias and control element of this circuit. The ZNBG provides the negative rail, FET bias control, polarisation switch control, tone detection and band switching with the minimum of external components ...
Page 13
... Figure 1 L grounded OV Figure 2 L connected OSC ZNBG3113 ZNBG3114 4-135 ...
Page 14
... ZNBG3113 ZNBG3114 CONNECTION DIAGRAM ORDERING INFORMATION Part Number Package ZNBG3113Q20 QSOP20 ZNBG3114Q20 QSOP20 Part Mark ZNBG3113 ZNBG3114 4-136 ...
Page 15
... ZNBG3113 ZNBG3114 PACKAGE DIMENSIONS IDENTIFICATION RECESS FOR PIN 1 PIN No.1 PIN Millimetres Inches MIN MAX MIN MAX A 8.55 8.74 0.337 0.344 B 0.635 0.025 NOM C 1.42 1.52 0.056 0.06 D 0.20 0.30 0.008 0.012 E 3.81 3.99 0.15 0.157 F 1.35 1.75 0.053 0.069 G 0.10 0.25 0.004 0.01 J 5.79 6.20 0.228 0.244 K 0° 8° 0° 8° Page Number ...
Page 16
... The Company reserves the right to alter without notice the specification, design, price or conditions of supply of any product or service. ZNBG3113 ZNBG3114 Zetex (Asia) Ltd. These are supported by ...
Page 17
...