mn3610h Panasonic Corporation of North America, mn3610h Datasheet - Page 3

• Manufacturer Part Number: mn3610h
• Description: 2048-bit High-responsivity Ccd Linear Image Sensor
• Manufacturer: Panasonic Corporation of North America

MN3610H
<Inspection conditions>
Note 1) The photo response non-uniformity (PRNU) is defined by the following equation, where X
Note 2) The odd/even bit non-uniformity (O/E) is defined by the following equation, where X
Note 3) The Saturation output voltage (V
Note 4) The dark signal output voltage (V
Note 5) The dynamic range is defined by the following equation.
•
•
•
•
•
Responsivity
Photo response non-uniformity
Odd/even bit non-uniformity
Saturation output voltage
Saturation exposure
Dark signal output voltage
Dark signal output non-uniformity
Shift register total transfer efficiency
Output impedance
Dynamic range
Signal output pin DC level
Compensation output pin DC level
Signal and compensation output pin DC level difference
to F=10).
Ta=25˚C, V
Light source: Daylight type fluorescent lamp
Optical system: A slit with an aperture dimensions of 20mm 20mm is used at a distance of 200mm from the sensor (equivalent
Load resistance = 100k Ohms
These specifications apply to the 2048 valid pixels excluding the dummy pixels D1 to D6.
Optical Characteristics
of the 2048 valid pixels and x is the absolute value of the difference between X
minimum) output pixel, when the surface of the photo-sites is illuminated with light having a uniform distribution over the
entire surface.
The incident light intensity shall be 50% of the standard saturation light intensity.
the 2048 valid pixels and Xn is the output voltage of the ‘n’th pixel, when the surface of the photo-sites is illuminated with
light having a uniform distribution over the entire surface.
In other words, this is the value obtained by dividing the average of the output difference between the odd and even pixels
by the average output voltage of all the valid pixels. The incident light intensity shall be 50% of the standard saturation
light intensity.
characteristics cannot be maintained as the incident light intensity is increased. (The light intensity of exposure at this
point is called the saturation exposure.)
Ta=25˚C and T
T
The dark signal output non-uniformity (DSNU) is defined as the difference between the maximum output voltage among
all the valid pixels and V
Since the dark signal voltage is proportional to the accumulation time, the dynamic range becomes wider when the
accumulation time is shorter.
int
.
Parameter
PRNU=
O/E=
DD
DR=
=12V, V
2047
n=1
| Xn–Xn
V
V
int
øH
SAT
2047 X
DRK
X
=10ms. Normally, the dark output voltage doubles for every 8 to 10˚C rise in Ta, and is proportional to
=V
ave
x
SH
+1
=V
DRK
|
ave
RH
100 (%)
V
=5V (pulse), f
in the dark condition at Ta=25˚C and T
Symbol
PRNU
DSNU
OS
STTE
V
O/E
V
V
V
DR
SE
Z
DRK
R
SAT
OS
– V
DS
O
100 (%)
SAT
DRK
DS
) is defined as the output voltage at the point when the linearity of the photoelectric
) is defined as the average output voltage of the 2048 pixels in the dark condition at
Note 1
Note 2
Note 3
Note 3
Dark condition, see Note 4
Dark condition, see Note 4
Note 5
Note 6
Note 6
Note 6
C
=0.5MHz, f
V
DSNU
DRK
R
=1MHz, T
Condition
int
int
(accumulation time)=10ms
=10ms.
ave
and the voltage of the maximum (or
CCD Linear Image Sensor
ave
10.0
0.10
min
is the average output voltage of
1.5
3.5
3.5
—
—
—
—
92
—
—
—
ave
is the average output voltage
5000
12.0
0.17
typ
2.0
0.4
0.2
4.5
4.5
—
—
—
—
20
max
14.0
100
1.0
2.0
6.0
6.0
10
—
—
—
—
3
1
V/lx·s
Unit
mV
mV
mV
lx·s
k
%
%
%
V
V
V