icx058cl Sony Electronics, icx058cl Datasheet
icx058cl
Available stocks
Related parts for icx058cl
icx058cl Summary of contents
Page 1
... Diagonal 6mm (Type 1/3) CCD Image Sensor for EIA Black-and-White Video Camera Description The ICX058CL is an interline CCD solid-state image sensor suitable for EIA black-and-white video cameras. Compared with the current product ICX058AL, sensitivity is improved drastically through the adoption of Super HAD CCD technology. ...
Page 2
... – GND – SUB – 2 – ICX058CL 1 Note) Note) : Photo sensor 16 Description Output amplifier drain supply GND Substrate (Overflow drain) Protective transistor bias Reset gate clock Horizontal register final stage transfer clock Horizontal register transfer clock Horizontal register transfer clock ...
Page 3
... Vss and SUB pins, while pins that are not tested DD OUT , Vss and – 3 – ICX058CL Typ. Max. Unit Remarks 15.0 15. 4.2 4.65 ±5% 820 resistor Unit Remarks ...
Page 4
... V –0.05 0 0.05 V 4.5 5.0 5.5 V 0.8 V RGLL 22.5 23.5 24 connected to the horizontal transfer clock input 1 Min. Unit Typ. Max. –0 0.2 8.5 V 9.0 9.5 – 4 – ICX058CL Waveform Remarks diagram )/2 VH VH1 VH2 )/2 VL VL3 VL4 n– ...
Page 5
... GND V23 V13 Horizontal transfer clock equivalent circuit – 5 – ICX058CL Typ. Max. Unit Remarks 1000 pF 560 pF 470 pF 330 pF 220 pF 100 270 ...
Page 6
... twh VHL V VHL V VL3 VHL V VLH V VLL V VL4 – 6 – ICX058CL VHH V VH VHH V VHL V VH3 V VLH V VLL VHH VHH V VHL V VHL V VH4 VLH V VL ...
Page 7
... RGH – RGH RGL tr twh twl Point A is the minimum value of the coupling waveform during the period from RGLL and V . RGLH RGLL – 7 – ICX058CL twl tr twh tf V RGH 0.5V RGL V RGL ...
Page 8
... H · two Symbol Min. Typ – 8 – ICX058CL Unit Remarks During 0.5 µs readout 1 15 250 ns 17 0.01 µs 0. During 0.5 0.5 µs drain charge rising side of the H · LH ...
Page 9
... Effective pixel region 10 Min. Typ. Max. Unit Measurement method 360 460 mV 600 mV 0.002 0.007 % 0 494 (V) 10 – 9 – ICX058CL (Ta = 25°C) Remarks 60° Zone 0 and I 4 Zone 0 to II’ 60° 60° ...
Page 10
... Dark signal Measure the average value of the signal output (Vdt [mV]) with the device ambient temperature 60°C and the device in the light-obstructed state, using the horizontal idle transfer level as a reference color temperature of 3200K halogen source subject. – 10 – ICX058CL ...
Page 11
... Adjust the signal output value generated by strobe light to 200mV. After setting the strobe light so that it strobes with the following timing, measure the residual signal (Vlag). Substitute the value into the following formula. Lag = (Vlag/200) 100 [%] FLD SG1 Light Strobe light timing Output Signal output 200mV Vlag (lag) – 11 – ICX058CL ...
Page 12
... ICX058CL ...
Page 13
... Spectral Sensitivity Characteristics (Includes lens characteristics, excludes light source characteristics) 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 400 500 Sensor Readout Clock Timing Chart Odd Field Even Field V3 V4 700 600 800 Wave Length [nm] 2.5 1.6 2.5 2.5 2.5 40.4 0.2 – 13 – ICX058CL 900 1000 Unit : µs ...
Page 14
... ICX058CL ...
Page 15
... ICX058CL ...
Page 16
... If a load is applied to the entire surface by a hard component, bending stress may be generated and the package may fracture, etc., depending on the flatness of the bottom of the package. Therefore, for installation, use either an elastic load, such as a spring plate adhesive. 50N 50N Compressive strength – 16 – ICX058CL 1.2Nm Torsional strength ...
Page 17
... Exposure to high temperature or humidity will affect the characteristics. Accordingly avoid storage or usage in such conditions. c) The brown stain may be seen on the bottom or side of the package. But this does not affect the CCD characteristics. – 17 – ICX058CL ...
Page 18
... ICX058CL ...