S29GL-A SPANSION [SPANSION], S29GL-A Datasheet - Page 51
S29GL-A
Manufacturer Part Number
S29GL-A
Description
S29GL-A MirrorBit Flash Family
Manufacturer
SPANSION [SPANSION]
Datasheet
1.S29GL-A.pdf
(89 pages)
- Current page: 51 of 89
- Download datasheet (4Mb)
April 22, 2005 S29GL-A_00_A3
Program Suspend/Program Resume Command Sequence
The Program Suspend command allows the system to interrupt a programming
operation or a Write to Buffer programming operation so that data can be read
from any non-suspended sector. When the Program Suspend command is writ-
ten during a programming process, the device halts the program operation
within 15 µs maximum (5µs typical) and updates the status bits. Addresses are
not required when writing the Program Suspend command.
After the programming operation is suspended, the system can read array data
from any non-suspended sector. The Program Suspend command may also be
issued during a programming operation while an erase is suspended. In this
case, data may be read from any addresses not in Erase Suspend or Program
Suspend. If a read is needed from the Secured Silicon Sector area (One-time
Program area), then user must use the proper command sequences to enter and
exit this region. Note that the Secured Silicon Sector, autoselect, and CFI func-
tions are unavailable when a program operation is in progress.
The system may also write the autoselect command sequence when the device
is in the Program Suspend mode. The system can read as many autoselect codes
as required. When the device exits the autoselect mode, the device reverts to
the Program Suspend mode, and is ready for another valid operation. See
toselect Command Sequence on page 44
After the Program Resume command is written, the device reverts to program-
ming. The system can determine the status of the program operation using the
Note: See
A d v a n c e
Table 30 on page 54
Increment Address
Figure 4. Program Operation
S29GL-A MirrorBit™ Flash Family
I n f o r m a t i o n
Embedded
in progress
algorithm
Program
and
Table 31 on page 55
No
for more information.
Command Sequence
Write Program
Last Address?
Programming
from System
Verify Data?
Completed
Data Poll
START
Yes
Yes
for program command sequence.
No
Au-
49
Related parts for S29GL-A
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
1 Gigabit, 512 Megabit, 256 Megabit and 128 Megabit 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology
Manufacturer:
SPANSION [SPANSION]
Datasheet:
Part Number:
Description:
3.0 Volt-only Page Mode Flash Memory Featuring 90 Nm Mirrorbit Process Technology
Manufacturer:
Meet Spansion Inc.
Datasheet:
Part Number:
Description:
TS 48/CIVIL/1-BIT ECC, X8 I/O AND 3V VCC SPANSION SLC NAND
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
TS 48/CIVIL/1-BIT ECC, X8 I/O AND 3V VCC SPANSION SLC NAND
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
MBM29F400TC-70PFTNSPANSION [FLASH MEMORY CMOS 4M (512K x 8/256K x 16) BIT]
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
AM29F010B70JI1 Megabit (128 K x 8-bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
S29AL016D70BAI02016 MEGABIT CMOS 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
S29AL016M90FAI01016 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
S29AL016M90FAI02016 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet: