ADSP-BF522 AD [Analog Devices], ADSP-BF522 Datasheet - Page 23

• Manufacturer Part Number: ADSP-BF522
• Description: Blackfin Embedded Processor
• Manufacturer: AD [Analog Devices]

Preliminary Technical Data
Table 10. Signal Descriptions (Continued)
Signal Name
USB 2.0 HS OTG
Port F: GPIO and Multiplexed Peripherals
Port G: GPIO and Multiplexed Peripherals
USB_DP
USB_DM
USB_XI
USB_XO
USB_ID
USB_VREF
USB_RSET
USB_VBUS
PF0/PPI D0/DR0PRI /ND_D0A
PF1/PPI D1/RFS0/ND_D1A
PF2/PPI D2/RSCLK0/ND_D2A
PF3/PPI D3/DT0PRI/ND_D3A
PF4/PPI D4/TFS0/ND_D4A/TACLK0
PF5/PPI D5/TSCLK0/ND_D5A/TACLK1
PF6/PPI D6/DT0SEC/ND_D6A/TACI0
PF7/PPI D7/DR0SEC/ND_D7A/TACI1
PF8/PPI D8/DR1PRI
PF9/PPI D9/RSCLK1/SPISEL6
PF10/PPI D10/RFS1/SPISEL7
PF11/PPI D11/TFS1/CZM
PF12/PPI D12/DT1PRI/SPISEL2/CDG
PF13/PPI D13/TSCLK1/SPISEL3/CUD
PF14/PPI D14/DT1SEC/UART1TX
PF15/PPI D15/DR1SEC/UART1RX/TACI3
Type Function
I/O
I/O
I
O
I
I
I
I/O 5V USB VBUS (USB_VBUS is an output only during initialization of USB OTG
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
Rev. PrG | Page 23 of 80 | February 2009
Data + (This ball should be pulled low when USB is unused or not present.) F
Data - (This ball should be pulled low when USB is unused or not present.)
USB Crystal Input (This ball should be pulled low when USB is unused or not
present.)
USB Crystal Output (This ball should be left unconnected when USB is unused
or not present.)
USB OTG mode (This ball should be pulled low when USB is unused or not
present.)
USB voltage reference (Connect to GND through a 0.1 F capacitor, or leave
unconnected if USB is unused or not present.)
USB resistance set. (This ball should be left unconnected when USB is unused
or not present.)
session request pulses. Host mode or OTG type A mode require that an
external voltage source of 5V, at 8mA or more–per the OTG specification–be
applied to VBUS. Other OTG modes require that this external voltage be
disabled. This ball should be pulled low when USB is unused or not present.)
GPIO/PPI Data 0/SPORT0 Primary Receive Data
/NAND Alternate Data 0
GPIO/PPI Data 1/SPORT0 Receive Frame Sync
/NAND Alternate Data 1
GPIO/PPI Data 2/SPORT0 Receive Serial Clock
/NAND Alternate Data 2/Alternate Capture Input 0
GPIO/PPI Data 3/SPORT0 Transmit Primary Data
/NAND Alternate Data 3
GPIO/PPI Data 4/SPORT0 Transmit Frame Sync
/NAND Alternate Data 4/Alternate Timer Clock 0
GPIO/PPI Data 5/SPORT0 Transmit Serial Clock
/NAND Alternate Data 5/Alternate Timer Clock 1
GPIO/PPI Data 6/SPORT0 Transmit Secondary Data
/NAND Alternate Data 6/Alternate Capture Input 0
GPIO/PPI Data 7/SPORT0 Receive Secondary Data
/NAND Alternate Data 7/Alternate Capture Input 1
GPIO/PPI Data 8/SPORT1 Primary Receive Data
GPIO/PPI Data 9/SPORT1 Receive Serial Clock/SPI Slave Select 6
GPIO/PPI Data 10/SPORT1 Receive Frame Sync/SPI Slave Select 7
GPIO/PPI Data 11/SPORT1 Transmit Frame Sync/Counter Zero Marker
GPIO/PPI Data 12/SPORT1 Transmit Primary Data/SPI Slave Select 2/Counter
Down Gate
GPIO/PPI Data 13/SPORT1 Transmit Serial Clock/SPI Slave Select 3/Counter Up
Direction
GPIO/PPI Data 14/SPORT1 Transmit Secondary Data/UART1 Transmit
GPIO/PPI Data 15/SPORT1 Receive Secondary Data
/UART1 Receive /Alternate Capture Input 3
ADSP-BF522/523/524/525/526/527
Driver
Type
F
F
F
C
C
D
C
C
D
C
C
C
D
C
C
C
D
C
C
1