MAX2366 MAXIM [Maxim Integrated Products], MAX2366 Datasheet - Page 4

• Manufacturer Part Number: MAX2366
• Description: Complete Dual-Band Quadrature Transmitters
• Manufacturer: MAXIM [Maxim Integrated Products]

Complete Dual-Band
Quadrature Transmitters
ELECTRICAL CHARACTERISTICS (continued)
(MAX2366/67/68 evaluation kit: 50Ω system, operating modes as defined in Table 6, input voltage at I and Q = 200mV
tial, common mode = V
ter, REF = 200mVp-p at 19.68MHz, V
LOL input power = -7dBm, f
= 1880MHz, f
Note 1: See Table 6 for register settings.
Note 2: ACPR is met over the specified V
Note 3: V
Note 4: Guaranteed by design and characterization.
Note 5: When enabled, turbolock is active during acquisition and injects boost current in addition to the normal charge-pump current.
Note 6: Charge Pump Compliance range is 0.5V to V
Note 7: >25°C guaranteed by production test. <25°C guaranteed by design and characterization.
4
IF_PLL
RF_PLL
Reference Frequency
Frequency Reference Signal Level
IF Main Divide Ratio
IF Reference Divide Ratio
VCO Operating Range
IF LO Output Power
Charge-Pump Source/Sink Current
Turbolock Boost Current
Charge-Pump Source/Sink Matching
Charge-Pump High-Z Leakage
RF Main Divide Ratio
RF Reference Divide Ratio
Maximum Phase-Detector Comparison
Frequency
Charge-Pump Source/Sink Current
Turbolock Boost Current
Charge-Pump Source/Sink Matching
Charge-Pump High-Z Leakage
RFPLL Input Sensitivity
_______________________________________________________________________________________
CM
RFL
must be supplied by the I/Q baseband source with ±6µA capability.
PARAMETER
= 836MHz, T
CC
/2,300kHz quadrature CW tones, RF and IF synthesizers locked with passive lead-lag second-order loop fil-
LOL
A
= +25°C, unless otherwise noted.)
= 966MHz, f
CC
= SHDN = IDLE = CS = TXGATE = +2.75V, V
CM
LOH
range.
VCO = 0
VCO = 1
BUF_EN = 1
ICP = 00 (Note 7)
ICP = 01 (Note 7)
ICP = 10 (Note 7)
ICP = 11 (Note 7)
(Note 5, 7)
Locked, all values of ICP, over specified
compliance range (Note 6)
Over specified compliance range (Note 6)
RCP = 00 (Note 7)
RCP = 01 (Note 7)
RCP = 10 (Note 7)
RCP = 11 (Note 7)
(Note 5, 6)
Locked, all values of RCP, over specified
compliance range (Note 6, 7)
Over specified compliance range (Note 6)
= 1750MHz, IFINH = 125mV
CC
- 0.5V.
CONDITIONS
RMS
at 130MHz, IS-95 CDMA modulation f
BAT
= +2.75V, IF output load = 400Ω, LOH,
4096
MIN
256
115
145
235
300
265
100
100
135
210
270
245
160
0.1
5
2
2
240–470
240–600
TYP
175
235
350
465
450
165
165
230
340
450
435
10
-6
5
5
262144
16384
MAX
2048
8192
230
315
470
625
615
225
225
310
460
630
630
0.6
30
10
10
RMS
RFH0
differen-
UNITS
mVp-p
= f
MHz
MHz
dBm
MHz
Vp-p
µA
µA
nA
µA
µA
µA
nA
%
%
RFH1