M34D64-W_08 STMICROELECTRONICS [STMicroelectronics], M34D64-W_08 Datasheet
M34D64-W_08
Related parts for M34D64-W_08
M34D64-W_08 Summary of contents
Page 1
... Features 2 ■ Two-wire I C serial interface supports 400 kHz protocol ■ Single supply voltage: – 2.5 to 5.5 V for M34D64-W ■ Hardware write control of the top quarter of memory ■ byte and page write ( bytes) ■ Random and Sequential Read modes ■ ...
Page 2
... Memory addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3.6 Write operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3.7 Byte Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 3.8 Page Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 3.9 Minimizing system delays by polling on ACK . . . . . . . . . . . . . . . . . . . . . . 16 3.10 Read operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 3.11 Random Address Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 3.12 Current Address Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 3.13 Sequential Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 3.14 Acknowledge in Read mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 4 Initial delivery state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 2/ Operating supply voltage Power-up conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Device reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Power-down conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 M34D64-W ...
Page 3
... M34D64-W 5 Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 7 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 8 Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 9 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Contents 3/27 ...
Page 4
... Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Table 7. Operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Table 8. AC measurement conditions Table 9. Input parameters Table 10. DC characteristics Table 11. AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Table 12. SO8N – 8-lead plastic small outline, 150 mils body width, mechanical data . . . . . . . . . . . 24 Table 13. Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Table 14. Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 4/27 M34D64-W ...
Page 5
... M34D64-W List of figures Figure 1. Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Figure 2. SO connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Figure 3. Device select code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Figure 4. Memory map showing write control area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Figure 5. Maximum R value versus bus capacitance ( Figure bus protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Figure 7. Write mode sequences with (data write enabled Figure 8. ...
Page 6
... Description 1 Description The M34D64-W are I devices organized as 8192 x 8 bits. These devices are compatible with the I interface that uses a bidirectional databus and serial clock. The devices carry a built-in 4-bit Device Type Identifier code (1010) in accordance with the I The device behaves as a slave in the I by the serial clock ...
Page 7
... M34D64-W Figure 2. SO connections 1. See Package mechanical data M34D64 SCL SDA section for package dimensions, and how to identify pin-1. Description AI02851d 7/27 ...
Page 8
... M34xxx M34xxx 4.) from inadvertent write. The Write Control signal is used to enable ) write instructions to the top quarter of the memory area. IH M34D64-W . (Figure 5 indicates how CC Figure 3. When not connected (left Ai15122 , and write operations are allowed ...
Page 9
... M34D64-W 2.5 V ground the reference for the V SS 2.6 Supply voltage (V 2.6.1 Operating supply voltage V Prior to selecting the memory and issuing instructions to it, a valid and stable V within the specified [V secure a stable DC supply voltage recommended to decouple the V suitable capacitor (usually of the order 100 nF) close to the V pins ...
Page 10
... L 100 1000 Bus line capacitor (pF) M34D64-W AI03114C 2 ) for bus BUS 400 kHz, t LOW = 1.3 µs R bus x C bus time V CC constant must be less than 500 ns R bus SCL I²C bus master SDA C bus M34D64 ai15127 ...
Page 11
... M34D64-W 2 Figure bus protocol SCL SDA SCL SDA Start condition SCL SDA Table 2. Device select code Device select code 1. The most significant bit, b7, is sent first. 2. E0, E1 and E2 are compared against the respective external pins on the memory device. Table 3. Most significant byte ...
Page 12
... The device that controls the data transfer is known as the bus master, and the other as the slave device. A data transfer can only be initiated by the bus master, which will also provide the serial clock for synchronization. The M34D64-W device is always a slave in all communications. ...
Page 13
... M34D64-W 3.5 Memory addressing To start communication between the bus master and the slave device, the bus master must initiate a Start condition. Following this, the bus master sends the Device Select Code, shown in Table 2.: Device select code The Device Select Code consists of a 4-bit Device Type Identifier, and a 3-bit Chip Enable “ ...
Page 14
... Dev sel Byte addr Byte addr R/W ACK ACK Data in N enabled), and waits for two address bytes. The device byte) is sent first, followed by the Least Significant Byte ( M34D64-W ACK ACK Data in ACK ACK Data in 1 Data in 2 AI01106d Figure 7.: Write mode : ) ...
Page 15
... M34D64-W 3.7 Byte Write After the Device Select code and the address bytes, the bus master sends one data byte. If the addressed location is Write-protected (top quarter of the memory), by Write Control (WC) being driven high, the location is not modified. The bus master terminates the transfer ...
Page 16
... NO Stop Data for the Write operation Continue the Write operation characteristics, but the typical time is shorter. To make use of this, a Figure 8.: Write cycle polling flowchart using M34D64-W Send address and receive ACK Start YES condition Device select with Continue the ...
Page 17
... M34D64-W Figure 9. Read mode sequences Current Address Read Random Address Read Sequential Current Read Sequential Random Read 1. The seven most significant bits of the Device Select Code of a Random Read (in the 1 must be identical. 3.10 Read operations Read operations are performed independently of the state of the Write Control (WC) signal. ...
Page 18
... For all Read commands, the device waits, after each byte read, for an acknowledgment th during the 9 bit time. If the bus master does not drive Serial Data (SDA) low during this time, the device terminates the data transfer and switches to its Standby mode. 18/27 sequences, without acknowledging the byte. Figure 9.: Read mode sequences. M34D64-W ...
Page 19
... M34D64-W 4 Initial delivery state The device is delivered with all bits in the memory array set to 1 (each byte contains FFh). 5 Maximum rating Stressing the device outside the ratings listed in cause permanent damage to the device. These are stress ratings only, and operation of the device at these, or any other conditions outside those indicated in the operating sections of this specification, is not implied ...
Page 20
... Pulse width ignored t NS (input filter on SCL and SDA) 1. Sampled only, not 100% tested. 20/27 Parameter Parameter Input levels 0.8V CC 0.2V CC (1) Parameter Test condition V < 0 > 0.7V IN Single glitch M34D64-W Min. Max. 2.5 5.5 –40 85 Min. Max. 100 50 0. 0. Input and output timing reference levels ...
Page 21
... M34D64-W Table 10. DC characteristics Symbol Input leakage current I LI (SCL, SDA) I Output leakage current LO I Supply current CC I Standby supply current CC1 Input low voltage (E2, E1, E0, SCL, SDA Input low voltage (WC) Input high voltage V IH (E2, E1, E0, SCL, SDA, WC) V Output low voltage ...
Page 22
... Data out hold time Clock low to next data valid (access time) Start condition setup time Start condition hold time Stop condition setup time Time between Stop condition and next Start condition Write time M34D64-W and Table 7.: Operating Min. Max. Unit 400 kHz ...
Page 23
... M34D64-W Figure 11. AC waveforms tCHCL SCL tDLCL SDA In tCHDX Start condition SCL SDA In tCHDH Stop condition SCL tCLQV SDA Out tCLCH tCLDX tDXCX SDA Change SDA Input tW Write cycle tCHCL tCLQX Data Valid DC and AC parameters tCHDH tDHDL Stop Start condition condition ...
Page 24
... Max 1.75 0.1 0.25 1.25 0.28 0.48 0.17 0.23 0.1 4.9 4 5.8 6.2 3.9 3 0.25 0.5 0° 8° 0.4 1.27 1. 45˚ c 0.25 mm GAUGE PLANE SO-A (1) inches Typ Min 0.0039 0.0492 0.011 0.0067 0.1929 0.189 0.2362 0.2283 0.1535 0.1496 0.05 - 0.0098 0° 0.0157 0.0409 M34D64-W Max 0.0689 0.0098 0.0189 0.0091 0.0039 0.1969 0.2441 0.1575 - 0.0197 8° 0.05 ...
Page 25
... Device tested with standard test flow Option blank = Standard packing T = Tape and reel packing Plating technology ® ECOPACK (RoHS compliant) For a list of available options (speed, package, etc.) or for further information on any aspect of this device, please contact your nearest ST sales office. Part numbering M34D64 – 25/27 ...
Page 26
... Addresses on Memory Map figure corrected. 2 5ms offered on certain versions of the device (bearing process identification letter “B”) M34D64-R root part number removed (R voltage range removed). TSSOP8 package removed. SO8N packages are ECOPACK® compliant. SO8N package specifications updated (sse mechanical data) ...
Page 27
... M34D64-W Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. ...