STK14D88_08 SIMTEK [Simtek Corporation], STK14D88_08 Datasheet
STK14D88_08
Related parts for STK14D88_08
STK14D88_08 Summary of contents
Page 1
... SRAM (the RECALL operation). Both STORE and RECALL operations are also available under software control. The Simtek nvSRAM is the first monolithic non-vola- tile memory to offer unlimited writes and reads the highest performance, most reliable non-volatile memory available. V Quatum Trap ...
Page 2
STK14D88 V CAP (TOP ...
Page 3
ABSOLUTE MAXIMUM RATINGS Voltage on Input Relative to Ground . . . . . . . . . . . . . –0.5V to 4.1V Voltage on Input Relative ...
Page 4
STK14D88 AC TEST CONDITIONS Input Pulse Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to ...
Page 5
SRAM READ CYCLES #1 & #2 SYMBOLS NO Alt ELQV AVAV ELEH AVQV AVQV GLQV ...
Page 6
STK14D88 SRAM WRITE CYCLES #1 & #2 SYMBOLS NO Alt AVAV AVAV WLWH WLEH ELWH ELEH DVWH DVEH DW ...
Page 7
AutoStore™/POWER-UP RECALL SYMBOLS NO. Standard Alternate 22 t HRECALL STORE HLHZ 24 V SWITCH 25 V CCRISE Note i: t starts from the time V HRECALL Note SRAM WRITE has not taken place since ...
Page 8
STK14D88 SOFTWARE-CONTROLLED STORE/RECALL CYCLE Symbols NO. E Cont Alternate STORE / RECALL Initiation Cycle Time AVAV Address Set-up Time AVEL Clock Pulse Width ELEH Address Hold ...
Page 9
HARDWARE STORE CYCLE SYMBOLS Standard Alternate DELAY HLQZ HLHX Note n: Read and Write cycles in Progress before HSB is asserted are given this minimum amount of time to complete. HARDWARE STORE CYCLE ...
Page 10
STK14D88 MODE SELECTION Notes q: The six consecutive addresses must be in the order listed. W ...
Page 11
... WRITE cycle and must remain stable until either goes high at the end of the cycle. The data on the common I/O pins DQ0-7 will be written into memory valid t before the end controlled WRITE or t before the end controlled WRITE. ...
Page 12
... During the STORE cycle, previous data is erased and then the new data is programmed into the non- volatile elements. Once a STORE cycle is initiated, further memory inputs and outputs are disabled until the cycle is completed. Document Control #ML0033 Rev 2.0 Jan 2008 ...
Page 13
... AA, 55, 00, FF, A5, or 5A. End product’s firmware should not assume an NV array set programmed state. Routines that check memory content val- ues to determine first time system configuration, cold or warm boot status, etc. should always pro- gram a unique NV pattern (e ...
Page 14
... STK14D88 NOISE CONSIDERATIONS The STK14D88 is a high-speed memory and so must have a high-frequency bypass capacitor of 0.1 µF connected between both V ground plane with no plane break to chip V leads and traces that are as short as possible. As with all high-speed CMOS ICs, careful routing of power, ground, and signals will reduce circuit noise. ...
Page 15
ORDERING INFORMATION STK14D88 Document Control #ML0033 Rev 2.0 Jan 2008 Packaging Option Blank= Tube TR= Tape & Reel Temperature Range Blank=Commercial ( Industrial (-45 to +85 C) Access Time 25=25 ns 35=35 ...
Page 16
STK14D88 Ordering Codes Part Number Description STK14D88-NF25 3V 32Kx 8 AutoStore nvSRAM SOP32-300 STK14D88-NF35 3V 32Kx 8 AutoStore nvSRAM SOP32-300 STK14D88-NF45 3V 32Kx 8 AutoStore nvSRAM SOP32-300 STK14D88-NF25TR 3V 32Kx 8 AutoStore nvSRAM SOP32-300 STK14D88-NF35TR 3V 32Kx 8 AutoStore nvSRAM ...
Page 17
Pin 300 mil SOIC Pin 1 Index 0.026 0.66 ( 0.032 0.81 0.12 0. 0.014 0.36 0.020 0.51 0.006 0. 0.013 0.32 Document Control #ML0033 Rev 2.0 Jan 2008 PACKAGE DRAWINGS 0.810 20. ...
Page 18
STK14D88 48 Pin 300 mil SSOP 0.400 ) ( 10.16 10.41 0.410 7.42 0.292 ) ( 0.299 7.59 .045 ( ) 11.43 .055 13.97 Pin 1 indicator .045 DIA. (11.43) .020 (5.1) SIDE VIEW 0.008 0.025 (0.635) 0.0135 0.620 ( ...
Page 19
Document Revision History Rev Date 1.0 December 2004 1.1 February 2005 1.3 August 2005 1.4 December 2005 1.5 February 2006 1.6 March 2006 Document Control #ML0033 Rev 2.0 Jan 2008 Change Initial Revision Fixed Number of pins typographical error, “R” ...
Page 20
STK14D88 1.7 February 2007 2.0 January 2008 SIMTEK STK14D88 Datasheet, January 2008 Copyright 2008, Simtek Corporation. All rights reserved. This datasheet may only be printed for the expressed use of Simtek Customers. No part of the datasheet may be reproduced ...