M38867E8AHP MITSUBISHI [Mitsubishi Electric Semiconductor], M38867E8AHP Datasheet - Page 28

• Manufacturer Part Number: M38867E8AHP
• Description: SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER??
• Manufacturer: MITSUBISHI [Mitsubishi Electric Semiconductor]

Fig. 24 Operation of UART serial I/O1 function
28
[Serial I/O1 Control Register (SIO1CON)]
001A
The serial I/O1 control register consists of eight control bits for the
serial I/O function.
[UART Control Register (UARTCON)] 001B
The UART control register consists of four control bits (bits 0 to 3)
which are valid when asynchronous serial I/O is selected and set
the data format of an data transfer and one bit (bit 4) which is al-
ways valid and sets the output structure of the P4
[Serial I/O1 Status Register (SIO1STS)]
0019
The read-only serial I/O1 status register consists of seven flags
(bits 0 to 6) which indicate the operating status of the serial I/O
function and various errors.
Three of the flags (bits 4 to 6) are valid only in UART mode.
The receive buffer full flag (bit 1) is cleared to “0” when the receive
buffer register is read.
If there is an error, it is detected at the same time that data is
transferred from the receive shift register to the receive buffer reg-
ister, and the receive buffer full flag is set. A write to the serial I/O1
status register clears all the error flags OE, PE, FE, and SE (bit 3
to bit 6, respectively). Writing “0” to the serial I/O1 enable bit SIOE
(bit 7 of the serial I/O control register) also clears all the status
flags, including the error flags.
Bits 0 to 6 of the serial I/O1 status register are initialized to “0” at
reset, but if the transmit enable bit (bit 4) of the serial I/O1 control
register has been set to “1”, the transmit shift completion flag (bit
2) and the transmit buffer empty flag (bit 0) become “1”.
T r a n s m i t o r r e c e i v e c l o c k
T r a n s m i t b u f f e r w r i t e
R e c e i v e b u f f e r r e a d
16
S e r i a l o u t p u t T
16
N o t e s
S e r i a l i n p u t R
1 : E r r o r f l a g d e t e c t i o n o c c u r s a t t h e s a m e t i m e t h a t t h e R B F f l a g b e c o m e s “ 1 ” ( a t 1 s t s t o p b i t , d u r i n g r e c e p t i o n ) .
2 : A s t h e t r a n s m i t i n t e r r u p t ( T I ) , w h e n e i t h e r t h e T B E o r T S C f l a g b e c o m e s “ 1 , ” c a n b e s e l e c t e d t o o c c u r d e p e n d i n g o n t h e s e t t i n g o f t h e t r a n s m i t
3 : T h e r e c e i v e i n t e r r u p t ( R I ) i s s e t w h e n t h e R B F f l a g b e c o m e s “ 1 . ”
4 : A f t e r d a t a i s w r i t t e n t o t h e t r a n s m i t b u f f e r w h e n T S C = 1 , 0 . 5 t o 1 . 5 c y c l e s o f t h e d a t a s h i f t c y c l e i s n e c e s s a r y u n t i l c h a n g i n g t o T S C = 0 .
s i g n a l
s i g n a l
i n t e r r u p t s o u r c e s e l e c t i o n b i t ( T I C ) o f t h e s e r i a l I / O 1 c o n t r o l r e g i s t e r .
X
X
D
D
T B E = 0
T S C = 0
T B E = 1
S T
S T
D
D
0
0
T B E = 0
D
D
5
1
1
/T
1 s t a r t b i t
7 o r 8 d a t a b i t
1 o r 0 p a r i t y b i t
1 o r 2 s t o p b i t ( s )
X
D pin.
16
[Transmit Buffer Register/Receive Buffer
Register (TB/RB)] 0018
The transmit buffer register and the receive buffer register are lo-
cated at the same address. The transmit buffer is write-only and
the receive buffer is read-only. If a character bit length is 7 bits, the
MSB of data stored in the receive buffer is “0”.
[Baud Rate Generator (BRG)] 001C
The baud rate generator determines the baud rate for serial trans-
fer.
The baud rate generator divides the frequency of the count source
by 1/(n + 1), where n is the value written to the baud rate genera-
tor.
R B F = 1
S P
S P
T B E = 1
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
S T
S T
D
0
D
0
MITSUBISHI MICROCOMPUTERS
R B F = 0
D
D
1
1
G e n e r a t e d a t 2 n d b i t i n 2 - s t o p - b i t m o d e
16
3886 Group
16
S P
T S C = 1
R B F = 1
S P