LTM8020EV-PBF LINER [Linear Technology], LTM8020EV-PBF Datasheet - Page 9

• Manufacturer Part Number: LTM8020EV-PBF
• Description: 200mA, 36V DC/DC ?Module
• Manufacturer: LINER [Linear Technology]

APPLICATIONS INFORMATION
PCB Layout
Most of the headaches associated with PCB layout have
been alleviated or even eliminated by the high level of
integration of the LTM8020. The LTM8020 is never-the-
less a switching power supply, and care must be taken to
minimize EMI and ensure proper operation. Even with the
high level of integration, you may fail to achieve specifi ed
operation with a haphazard or poor layout. See Figure 3
for a suggested layout.
Ensure that the grounding and heatsinking are acceptable.
A few rules to keep in mind are:
1. Place the C
2. Place the C
3. Place the C
4. Connect all of the GND connections to as large a copper
5. The copper pours also serve as the heatsink for the
and GND connection of the LTM8020.
V
ground current fl ows directly adjacent or underneath
the LTM8020.
pour or plane area as possible on the top layer. Avoid
breaking the ground connection between the external
components and the LTM8020.
LTM8020. Place several vias in the GND plane to act as
heat pipes to other layers of the printed circuit board.
OUT
and GND connection of the LTM8020.
Figure 3. Layout showing suggested external
components, GND plane and thermal vias
SHDN
IN
OUT
IN
COPPER
capacitor as close as possible to the V
V
IN
C
and C
ADJ
IN
capacitor as close as possible to the
OUT
R
ADJ
capacitors such that their
BIAS
VIAs TO GND PLANE
GND
C
V
OUT
8020 F03
OUT
IN
Positive to Negative Voltage Regulation
The LTM8020 can generate a negative output by tying the
V
in the Typical Applications section. In this confi guration,
SHDN must be level shifted or referenced to GND, and the
available output current may be reduced.
Hot-Plugging Safely
The small size, robustness and low impedance of ceramic
capacitors make them an attractive option for the input
bypass capacitor of LTM8020. However, these capacitors
can cause problems if the LTM8020 is plugged into a live
supply (see Linear Technology Application Note 88 for
a complete discussion). The low loss ceramic capacitor
combined with stray inductance in series with the power
source forms an under damped tank circuit, and the volt-
age at the V
nominal input voltage, possibly exceeding the LTM8020’s
rating and damaging the part. If the input supply is poorly
controlled or the user will be plugging the LTM8020 into
an energized supply, the input network should be designed
to prevent this overshoot. Figure 4 shows the waveforms
that result when an LTM8020 circuit is connected to a 24V
supply through six feet of 24-gauge twisted pair. The fi rst
plot is the response with a 2.2μF ceramic capacitor at the
input. The input voltage rings as high as 35V and the input
current peaks at 20A. One method of damping the tank
circuit is to add another capacitor with a series resistor to
the circuit. In Figure 4b an aluminum electrolytic capacitor
has been added. This capacitor’s high equivalent series
resistance damps the circuit and eliminates the voltage
overshoot. The extra capacitor improves low frequency
ripple fi ltering and can slightly improve the effi ciency of the
circuit, though it is likely to be the largest component in the
circuit. An alternative solution is shown in Figure 4c. A 1Ω
resistor is added in series with the input to eliminate the
voltage overshoot (it also reduces the peak input current).
A 0.1μF capacitor improves high frequency fi ltering. This
solution is smaller and less expensive than the electrolytic
capacitor. For high input voltages its impact on effi ciency
is minor, reducing effi ciency less than one half percent for
a 5V output at full load operating from 24V.
OUT
pads to system ground and connecting GND as shown
IN
pin of the LTM8020 can ring to twice the
LTM8020
8020fb
9