ST62T15C ST Microelectronics, ST62T15C Datasheet - Page 11

no-image

ST62T15C

Manufacturer Part Number
ST62T15C
Description
(ST62T15C / ST62T25C) 8-BIT OTP/EPROM MCUs WITH A/D CONVERTER
Manufacturer
ST Microelectronics
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ST62T15C6
Manufacturer:
ST
Quantity:
113
Part Number:
ST62T15C6
Manufacturer:
ST
Quantity:
20 000
Part Number:
ST62T15C6.
Manufacturer:
ST
0
Part Number:
ST62T15CB6
Manufacturer:
ST
0
Part Number:
ST62T15CB6.
Manufacturer:
ST
0
Part Number:
ST62T15CM6
Manufacturer:
STM
Quantity:
2 508
Part Number:
ST62T15CM6
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
ST62T15CM6
Quantity:
24 000
Part Number:
ST62T15CM6/SWD
Manufacturer:
ST
0
PROGRAMMING MODES (Cont’d)
1.4.2 Program Memory
EPROM/OTP programming mode is set by a
+12.5V voltage applied to the TEST/V
programming flow of the ST62T15C,T25C/E25C is
described in the User Manual of the EPROM Pro-
gramming Board.
Table 2. ST62T15C Program Memory Map
Table 3. ST62T25C,E25C Program Memory Map
Device Address
Device Address
0FFCh-0FFDh
0FFCh-0FFDh
0FA0h-0FEFh
0FF8h-0FFBh
0FFEh-0FFF h
0FA0h-0FEFh
0FF8h-0FFBh
0FFEh-0FFF h
0880h-0F9Fh
0FF0h-0FF7h
0080h-0F9Fh
0FF0h-0FF7h
0000h-087Fh
0000h-007Fh
NMI Interrupt Vector
NMI Interrupt Vector
Interrupt Vectors
Interrupt Vectors
Reset Vector
Reset Vector
Description
Description
User ROM
User ROM
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
PP
pin. The
Note: OTP/EPROM devices can be programmed
with the development tools available from STMi-
croelectronics (ST62E2X-EPB or ST622X-KIT).
1.4.3 EPROM Erasing
The EPROM of the windowed package of the
MCUs may be erased by exposure to Ultra Violet
light. The erasure characteristic of the MCUs is
such that erasure begins when the memory is ex-
posed to light with a wave lengths shorter than ap-
proximately 4000Å. It should be noted that sun-
lights and some types of fluorescent lamps have
wavelengths in the range 3000-4000Å.
It is thus recommended that the window of the
MCUs packages be covered by an opaque label to
prevent unintentional erasure problems when test-
ing the application in such an environment.
The recommended erasure procedure of the
MCUs EPROM is the exposure to short wave ul-
traviolet light which have a wave-length 2537A.
The integrated dose (i.e. U.V. intensity x exposure
time) for erasure should be a minimum of 30W-
sec/cm
proximately 30 to 40 minutes using an ultraviolet
lamp with 12000 W/cm
ST62E25C should be placed within 2.5cm (1Inch)
of the lamp tubes during erasure.
2
. The erasure time with this dosage is ap-
ST62T15C/T25C/E25C
2
power rating. The
11/70
11

Related parts for ST62T15C