CXA2027 Sony Corporation, CXA2027 Datasheet
CXA2027
Available stocks
Related parts for CXA2027
CXA2027 Summary of contents
Page 1
... Analog signal processor IC For the availability of this product, please contact the sales office. Description The CXA2027Q is an analog signal processor for CCD linear image sensor output signal. This device is suitable for 3 lines of full-color CCD linear image sensor (ILX516K/ILX518K/ILX520K: 3648 pixels 3 lines/5363 pixels ...
Page 2
... S/H GCA S/H GCA S/H GCA LOG D/A LATCH D – 2 – GCA shift Driver REF 17 LOG LOG 16 D/A D/A LATCH LATCH CXA2027Q TD4 LCLP GC VCCP SIGOUT GND VRT VRB CLPC LD4 LD3 LD2 ...
Page 3
... SIGOUT output line clamp 1.8V voltage adjustment 6-bit data input pin 4 for SIGOUT output line clamp 100µ voltage adjustment 6-bit data input pin 5 for SIGOUT output line clamp voltage adjustment 6-bit data input pin 6 for SIGOUT output line clamp voltage adjustment (MSB) CXA2027Q ...
Page 4
... GCA gain adjustment (MSB) VCCA 1.5k Additional capacitance pin for line clamp. Add 0.47µF between this pin and GND. 6.7µ 2.0V Output pin for AD converter 100µ reference voltage VRB 100µ VCCA 2k Output pin for AD converter reference voltage VRT 4k GND pin CXA2027Q ...
Page 5
... DA2 analog output test pin DA3 analog output test pin Pixel clamp pulse input pin 250µ (Apply high level during the 1.5V precharge period of CCD output) MPX channel switching pulse input pin 1 1.2V (See high/low table under Pin 32 in following section.) 100µ CXA2027Q ...
Page 6
... Note 1) of CCD output) 1m 260µ Output test pin after MPX (use with open) 2k CCD signal R channel input pin 100µ 3.7V CCD signal G channel input pin CCD signal B channel input pin CXA2027Q Pin 20 SIGOUT R channel G channel B channel B channel ...
Page 7
... Voltage input pin for setting B channel pre-stage GCA gain adjustment latch circuit to data input mode (high) or hold mode (low). Power supply pin (for analog, general system) Power supply pin (for DA converter system) Reset level Precharge level Effective signal level CXA2027Q ...
Page 8
... Maximum clamp voltage 11111 Minimum clamp voltage 00000 Maximum DC output voltage 111111 Minimum DC output voltage 000000 Clamp ON High Clamp OFF Low – 8 – CXA2027Q Others LPR: for R-ch LPG: for G-ch LPB: for B-ch LD0: LSB LD4: MSB D4-0: LSB D4-4: MSB D5-0: LSB D5-4: MSB D6-0: LSB D6-5: MSB ...
Page 9
... SW35 SW35 Difference between output value 1/2 level for input level Vx and output level for input level 1/2 Vx 0.3V (SG35-2). See Note 2. SW11 SW16 = b, SW22 SW23 = b, SW31 ( ( (b, b), SW35 SW35 – 9 – CXA2027Q ( 25°C) CC Min. Typ. Max. Unit 44 ...
Page 10
... DC 63.6µs 7µ SG23 24 23 SW23 GCA 22 SW22-1 21 0.01µ 20 Driver V20 DC shift 19 1µ 18 V18 V REF 300 17 V17 LOG LOG 1µ 16 D/A D/A SW16 0.47µ LATCH LATCH 15 SW15 14 SW14 13 SW13 V20 (Vx) No 1.5V No 0.3V CXA2027Q SW22-2 3.1V ...
Page 11
... CCD signal (R-IN/ Precharge level G-IN/ B-IN) CLP SH MPX1 MPX2 SIGOUT Data taken converter Output channel B Reset level t4 t1 50 Min. Typ. t1 100ns t2 40ns 50ns t3 5ns 20ns t4 5ns t5 60ns Table 1 – 11 – Effective signal level 5ns 50 Max. CXA2027Q ...
Page 12
... CXA2027Q ...
Page 13
... Timing 3 (latch data input)] Latch gate (LPR/LPG/LPB) Input data (LD0 to LD4 (input data decision time) Min. Typ. t7 50ns t8 50ns t9 50ns t10 800ns Table 3 – 13 – t9 t10 Max. CXA2027Q ...
Page 14
... D6-0 to D6-5. The adjustment step is approximately 1mV/LSB. The standard settings are D6-0, D6-1 = “H”, D6-2 to D6-5 = “L”. 7. Pulse input signals Sharp edges at input pulse signals may affect output. If there is a problem, insert a damping resistor (around 100 to 200Ω) to smooth the pulse’s edges. – 14 – CXA2027Q n 1.05 [times] ...
Page 15
... CXA2027Q ...
Page 16
... D6-0 to D6-5 input data (expressed as decimal system) – 16 – 1MHz pin input voltage [V] SIGOUT clamp voltage adjustment range CXA2027Q 5 VRB 60 ...
Page 17
... Total gain supply voltage fluctuation DA1 all 0/ DA1 all 0/GC = open DA1 all 0/GC = GND DA1 all 1/ DA1 all 1/GC = open DA1 all 1/GC = GND Ta = 25° 1MHz 5 Vcc [V] SIGOUT SIGOUT – VRB Temperature [°C] CXA2027Q 5.25 70 ...
Page 18
... This product uses S-PdPPF (Sony Spec.-Palladium Pre-Plated Lead Frame). 48PIN QFP (PLASTIC 0.15 0.3 – 0.1 ± 0.12 M 2.2 – 0.15 PACKAGE STRUCTURE PACKAGE MATERIAL LEAD TREATMENT QFP-48P-L04 LEAD MATERIAL QFP048-P-1212-B PACKAGE WEIGHT – 18 – + 0.1 0.15 – 0.05 0.15 + 0.2 0.1 – 0.1 + 0.35 EPOXY RESIN SOLDER / PALLADIUM PLATING COPPER / 42 ALLOY 0.7g CXA2027Q ...