TLP350_07 TOSHIBA [Toshiba Semiconductor], TLP350_07 Datasheet - Page 2

• Manufacturer Part Number: TLP350_07
• Description: GaA?As IRED + Photo IC
• Manufacturer: TOSHIBA [Toshiba Semiconductor]

Absolute
Recommended Operating Conditions
Operating frequency
Storage temperature range
Operating temperature range
Lead soldering temperature (10 s)
Isolation voltage (AC, 1 minute, R.H. ≤ 60%)
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
Note 1: Pulse width P
Note 2: Exponential waveform pulse width P
Note 3: Exponential waveform I
Note 4: At 2 mm or more from the lead root.
Note 5: This device is regarded as a two terminal device: pins 1, 2, 3 and 4 are shorted together, as are pins 5, 6, 7
Note 6: A ceramic capacitor(0.1 μF) should be connected from pin 8 to pin 5 to stabilize the operation of the high
Input current, ON
Input voltage, OFF
Supply voltage
Peak output current
Operating temperature
Note: Recommended operating conditions are given as a design guideline to obtain expected performance of the
Note 7: Input signal rise time (fall time) < 0.5 μs.
Note 8: If the rising slope of the supply voltage (VCC) for the detector is steep, stable operation of the internal
Forward current
Forward current derating (Ta ≥ 85°C)
Peak transient forward current
Reverse voltage
Junction temperature
“H” peak output current
“L” peak output current
Supply voltage
Supply voltage Derating
Junction temperature
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even
if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum
ratings.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
(“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test
report and estimated failure rate, etc).
device. Additionally, each item is an independent guideline respectively. In developing designs using this
product, please confirm specified characteristics shown in this document.
Maximum Ratings
and 8.
gain linear amplifier. Failure to provide the bypass may impair the switching property.
The total lead length between capacitor and coupler should not exceed 1 cm.
circuits cannot be guaranteed.
Be sure to set 3.0V/μs or less for a rising slope of the VCC.
Characteristic
Characteristic
W
≤ 1 μs, 300 pps
(Note 7)
OPH
Ta = −40 to 100°C
(Ta = 25°C)
I
≥ -2.0A (≤ 0.3μs), I
OPH
V
Symbol
I
F (OFF)
F (ON)
(Note 2)
V
T
Ta < 95 °C
Ta ≥ 95 °C
CC
opr
/I
OPL
(Note 1)
(Note 3)
(Note 4)
(Note 5)
W
≤ 0.3μs, f ≤ 15kHz
Min
−40
7.5
15
⎯
0
ΔV
2
ΔI
Symbol
OPL
I
CC
I
V
T
BV
F
T
T
OPH
I
OPL
V
Typ.
FP
I
T
T
/ΔTa
CC
stg
opr
sol
f
F
⎯
⎯
⎯
⎯
⎯
R
j
j
/ΔTa
S
≤ 2.0A (≤ 0.3μs)
±2.0
Max
100
0.8
10
30
−55 to 125
−40 to 100
Rating
−0.54
3750
−2.5
125
-1.0
125
260
2.5
20
35
50
1
5
Unit
mA
°C
V
V
A
mA/°C
V /℃
Vrms
Unit
kHz
mA
°C
°C
°C
°C
°C
A
V
A
A
V
2007-10-01
TLP350