AD847SQ883B Analog Devices, AD847SQ883B Datasheet - Page 3

• Manufacturer Part Number: AD847SQ883B
• Description: OP Amp Single GP ?18V 8-Pin CDIP
• Manufacturer: Analog Devices

DSCC FORM 2234
APR 97
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer
Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-
PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying
activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan
may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.
These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MIL-
PRF-38535 is required to identify when the QML flow option is used.
in MIL-PRF-38535, appendix A and herein.
as specified in table I and shall apply over the full ambient operating temperature range.
tests for each subgroup are described in table I.
in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD PIN
number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device.
to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in
accordance with MIL-PRF-38535 to identify when the QML flow option is used.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
3.2.1 Case outline. The case outline shall be in accordance with 1.2.2 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
DEPARTMENT OF DEFENSE SPECIFICATION
DEPARTMENT OF DEFENSE STANDARDS
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
MIL-STD-883
MIL-STD-1835 -
MIL-HDBK-103 -
MIL-HDBK-780 -
DEFENSE SUPPLY CENTER COLUMBUS
(Copies of these documents are available online at
MICROCIRCUIT DRAWING
COLUMBUS, OHIO 43218-3990
-
STANDARD
Interface Standard Electronic Component Case Outlines.
Standard Microcircuit Drawings.
Test Method Standard Microcircuits.
List of Standard Microcircuit Drawings.
http://assist.daps.dla.mil/quicksearch/
SIZE
A
REVISION LEVEL
B
or from the Standardization
SHEET
5962-89647
3