MAX11359AETL Maxim Integrated, MAX11359AETL Datasheet - Page 54

• Manufacturer Part Number: MAX11359AETL
• Description: Analog to Digital Converters - ADC
• Manufacturer: Maxim Integrated

Specifications of MAX11359AETL

• Number Of Channels: 10
• Architecture: Sigma-Delta
• Conversion Rate: 10 SPs to 512 SPs
• Resolution: 16 bit
• Input Type: Differential
• Interface Type: 4-Wire Serial, Microwire, QSPI, SPI
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Power Dissipation: 2051.3 mW
• Number Of Converters: 1
• Voltage Reference: 1.251 V 1.996 V, 2.422 V

The IMSK register determines which bits of the STATUS
register generate an interrupt on INT. The bits in this
register do not mask output signals routed to UPIO
since the output signals are masked by disabling that
UPIO function.
MLDVD: LDVD status bit mask. Set MLDVD = 0 to
enable the LDVD status bit interrupt to INT, and set
MLDVD = 1 to mask the LDVD status bit interrupt. The
power-on default value is 1.
MLCPD: LCP status bit mask. Set MLCPD = 0 to
enable the LCP status bit interrupt to INT, and set
MLCPD = 1 to mask the LCP status bit interrupt. The
power-on default value is 1.
MADO: ADO status bit mask. Set MADO = 0 to enable
the ADO status bit interrupt to INT, and set MADO = 1
to mask the ADO status bit interrupt. The power-on
default value is 1.
MSDC: SDC status bit mask. Set MSDC = 0 to enable
the SDC status bit interrupt to INT, and set MSDC = 1
to mask the SDC status bit interrupt. The power-on
default value is 1.
MCRDY: CRD status bit mask. Set MCRDY = 0 to
enable the CRDY status bit interrupt to INT, and set
This register is the power-supply and voltage monitors
control register.
LDOE: Low-dropout linear-regulator enable bit. Set
LDOE = 1 to enable the low-dropout linear regulator to
provide the internal source voltage for the charge
pump. Set LDOE = 0 to disable the LDO, allowing an
external drive to the charge-pump input through REG.
The power-on default value is 0.
CPE: Charge-pump enable bit. Set CPE = 1 to enable the
charge-pump doubler, and set CPE = 0 to disable the
charge-pump doubler. The power-on default value is 0.
LSDE: DVDD low-supply voltage-detector power-
enable bit. Set LSDE = 1 to enable the +1.8V (DVDD)
low-supply-voltage detector, and set LSDE = 0 to
16-Bit Data-Acquisition System with ADC, DAC,
UPIOs, RTC, Voltage Monitors, and Temp Sensor
MAX11359A
IMSK Register (Power-On State: 1111 011X 1111 1111)
PS_VMONS Register (Power-On State: 0010 01XX)
54
MLDVD
MUPR4
LDOE
MSB
MSB
MLCPD
MUPR3
CPE
MUPR2
MADO
LSDE
MUPR1
MSDC
CPDE
MCRDY = 1 to mask the CRDY status bit interrupt. The
power-on default value is 0.
MADD: ADD status bit mask. Set MADD = 0 to enable
the ADD status bit interrupt to INT, and set MADD = 1
to mask the ADD status bit interrupt. The power-on
default value is 1.
MALD: ALD status bit mask. Set MALD = 0 to enable
the ALD status bit interrupt to INT, and set MALD = 1 to
mask the ALD status bit interrupt. The power-on default
value is 1.
MUPR<4:1>: UPR<4:1> status bits mask. Set MUPR_ =
0 to enable the UPR_ status bit interrupt to INT, and set
MUPR_ = 1 to mask the UPR_ status bit interrupt. (_ =
1, 2, 3, or 4 and corresponds to the UPIO1, UPIO2,
UPIO3, or UPIO4 pins, respectively.) The power-on
default value is F hex.
MUPF<4:1>: UPF<4:1> status bits mask. Set MUPF_ =
0 to enable the UPF_ status bit interrupt to INT, and set
MUPF_ = 1 to mask the UPF_ status bit interrupt. (_ = 1,
2, 3, or 4 and corresponds to the UPIO1, UPIO2,
UPIO3, or UPIO4 pins, respectively.) The power-on
default value is F hex.
disable the DVDD low-supply-voltage detector. The
power-on default value is 1.
CPDE: CPOUT low-supply voltage-detector power-
enable bit. Set CPDE = 1 to enable the +2.7V CPOUT
low-supply voltage-detector comparator, and set CPDE
= 0 to disable the CPOUT low-supply voltage-detector
comparator. The power-on default value is 0.
HYSE: DVDD low-supply voltage-detector hysteresis-
enable bit. Set HYSE = 1 to set the hysteresis for the
+1.8V (DVDD) low-supply-voltage detector to +200mV,
and set HYSE = 0 to set the hysteresis to +20mV. On initial
power-up, the hysteresis is +20mV and can be pro-
grammed to 200mV once RESET goes high. Once pro-
grammed to +200mV, the DVDD falling threshold is +1.8V
nominally and the rising threshold is +2.0V nominally. The
MCRDY
MUPF4
HYSE
MUPF3
MADD
RSTE
MUPF2
MALD
X
Maxim Integrated
MUPF1
LSB
LSB
X
X