STM32F372VCT6 STMicroelectronics, STM32F372VCT6 Datasheet - Page 14

• Manufacturer Part Number: STM32F372VCT6
• Description: ARM Microcontrollers - MCU 32-Bit ARM Cortex M4 72MHz 256kB MCU FPU
• Manufacturer: STMicroelectronics

Specifications of STM32F372VCT6

• Product Category: ARM Microcontrollers - MCU
• Rohs: yes
• Core: ARM Cortex M4F
• Processor Series: STM32F372xx
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 72 MHz
• Program Memory Size: 256 KB
• Data Ram Size: 32 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 2.4 V to 3.6 V
• Operating Temperature Range: - 40 C to + 85 C
• Package / Case: LQFP-100
• Mounting Style: SMD/SMT
• A/d Bit Size: 16 bit
• A/d Channels Available: 1
• Interface Type: CAN, I2C, SPI, USART, USB
• Length: 14 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Number Of Programmable I/os: 84
• Number Of Timers: 2
• On-chip Dac: Yes
• Program Memory Type: Flash
• Supply Voltage - Max: 3.6 V
• Supply Voltage - Min: 2.4 V

Functional overview
3.7
3.7.1
3.7.2
3.7.3
14/128
Power management
Power supply schemes
●
●
●
●
Power supply supervisor
●
●
The device features an embedded programmable voltage detector (PVD) that monitors the
V
when V
threshold. The interrupt service routine can then generate a warning message and/or put
the MCU into a safe state. The PVD is enabled by software.
Voltage regulator
The regulator has three operation modes: main (MR), low power (LPR), and power-down.
●
●
●
The voltage regulator is always enabled after reset. It is disabled in Standby mode.
DD
power supply and compares it to the V
V
through V
V
–
–
V
sigma delta ADCs. Independent from V
V
registers when V
The device has an integrated power-on reset (POR)/power-down reset (PDR) circuitry.
It is always active, and ensures proper operation starting from/down to 2 V. The device
remains in reset mode when V
need for an external reset circuit. The POR monitors only the V
During the startup phase it is required that V
or equal to V
The PDR monitors both the V
supply supervisor can be disabled (by programming a dedicated Option bit) to reduce
the power consumption if the application design ensures that V
equal to V
The MR mode is used in the nominal regulation mode (Run)
The LPR mode is used in Stop mode.
The power-down mode is used in Standby mode: the regulator output is in high
impedance, and the kernel circuitry is powered down thus inducing zero consumption.
DD :
DDA
DDSD12
BAT
DD
external analog power supplies for Reset blocks, RCs and PLL
supply voltage for 12-bit ADC, DACs and comparators (minimum voltage to be
applied to V
external power supply for I/Os and the internal regulator. It is provided externally
= 1.65 to 3.6 V: power supply for RTC, external clock 32 kHz oscillator and backup
= 2.0 to 3.6 V:
drops below the V
and V
DD
DD
.
DD
pins, and can be 2.0 to 3.6 V.
DDSD3
.
DDA
DD
is not present.
is 2.4 V when the 12-bit ADC and DAC are used).
= 2.2 to 3.6 V: supply voltages for SDADC1/2 and SDADCD3
PVD
Doc ID 022691 Rev 3
threshold and/or when V
DD
DD
and V
is below a specified threshold, V
PVD
DDA
DD
/V
threshold. An interrupt can be generated
supply voltages, however the V
DDA
DDA
.
should arrive first and be greater than
DD
is higher than the V
DDA
DD
POR/PDR
supply voltage.
is higher than or
, without the
STM32F37x
DDA
PVD
power