MAX7325ATG Maxim Integrated, MAX7325ATG Datasheet - Page 14

• Manufacturer Part Number: MAX7325ATG
• Description: Interface - I/O Expanders
• Manufacturer: Maxim Integrated
• Series: MAX7325r

Specifications of MAX7325ATG

• Maximum Operating Frequency: 400 KHz
• Operating Supply Voltage: 1.71 V to 5.5 V
• Operating Temperature Range: - 40 C to + 125 C
• Package / Case: TQFN-24 EP
• Power Dissipation: 761.9 mW

Typically, the master reads one byte from the push-pull
ports of the MAX7325, then issues a STOP condition
(Figure 8). However, the master can read two or more
bytes from the group B ports of the MAX7325, then
issues a STOP condition. In this case, the MAX7325
resamples the port outputs during each acknowledge
and transmits the new data each time.
A write to either output port groups of the MAX7325
starts with the master transmitting the group’s slave
address with the R/W bit set low. The MAX7325
acknowledges the slave address and samples the
ports during the acknowledge bit. INT goes high (high
impedance if an external pullup resistor is not fitted)
during the slave acknowledge only when it writes to the
open-drain ports. The master can now transmit one or
more bytes of data. The MAX7325 acknowledges these
subsequent bytes of data and updates the correspond-
ing group’s ports with each new byte until the master
issues a STOP condition (Figure 9).
The MAX7325’s SDA, SCL, AD0, AD2, RST, INT, O8–O15,
and P0–P7 are overvoltage protected to +6V. This
allows the MAX7325 to operate from a lower supply
voltage, such as +3.3V, while the I
any of the eight I/O ports are driven as inputs from a
higher logic level, such as +5V.
I
and 8 Open-Drain I/Os
MAX7325
Figure 9. Writing to the MAX7325
14
2
INTERNAL WRITE
C Port Expander with 8 Push-Pull
FROM PORT
DATA OUT
TO PORT
Port Input and I
SDA
SCL
Applications Information
START CONDITION
S
1
Translation from Higher or
2
SLAVE ADDRESS
3
Lower Logic Voltages
4
2
Writing the MAX7325
5
C Interface Level
2
6
C interface and/or
7
R/W ACKNOWLEDGE
0
8
A
FROM SLAVE
DATA TO INTERRUPT MASK
DATA 1
The MAX7325 can operate from a higher supply volt-
age, such as +3V, while the I
of the I/O ports P0–P7 are driven from a lower logic
level, such as +2.5V. For V+ < 1.8V, apply a minimum
voltage of 0.8 x V+ to assert a logic-high on any input.
For a V+ ≥ 1.8V, apply a voltage of 0.7 x V+ to assert a
logic-high. For example, a MAX7325 operating from a
+5V supply may not recognize a +3.3V nominal logic-
high. One solution for input-level translation is to drive
MAX7325 I/Os from open-drain outputs. Use a pullup
resistor to V+ or a higher supply to ensure a high logic
voltage greater than 0.7 x V+.
The open-drain output architecture allows for level trans-
lation to higher or lower voltages than the MAX7325’s
supply. Use an external pullup resistor on any output to
convert the high-impedance logic-high condition to a
positive voltage level. The resistor can be connected to
any voltage up to +6V, and the resistor value chosen to
ensure no more than 20mA is sunk in the logic-low condi-
tion. For interfacing CMOS inputs, a pullup resistor value
of 220kΩ is a good starting point. Use a lower resistance
to improve noise immunity, in applications where power
consumption is less critical, or where a faster rise time is
needed for a given capacitive load.
Each of the push-pull output ports has protection
diodes to V+ and GND. When a port output is driven to
a voltage higher than V+ or lower than GND, the appro-
priate protection diode clamps the output to a diode
drop above V+ or below GND. When the MAX7325 is
powered down (V+ = 0V), every output port’s protection
t
PV
Port Output Signal-Level Translation
A
ACKNOWLEDGE
FROM SLAVE
DATA TO INTERRUPT MASK
DATA 1 VALID
DATA 2
2
C interface and/or some
t
PV
A
ACKNOWLEDGE
FROM SLAVE
Maxim Integrated
DATA 2 VALID