IS24C02B-2ZLI-TR ISSI, Integrated Silicon Solution Inc, IS24C02B-2ZLI-TR Datasheet - Page 7

• Manufacturer Part Number: IS24C02B-2ZLI-TR
• Description: IC EEPROM 2KBIT 1MHZ 8TSSOP
• Manufacturer: ISSI, Integrated Silicon Solution Inc

Specifications of IS24C02B-2ZLI-TR

• Format - Memory: EEPROMs - Serial
• Memory Type: EEPROM
• Memory Size: 2K (256 x 8)
• Speed: 400kHz, 1MHz
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 1.8 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-TSSOP
• Density: 2Kb
• Interface Type: Serial (2-Wire)
• Organization: 256x8
• Access Time (max): 400ns
• Frequency (max): 1MHz
• Write Protection: Yes
• Data Retention: 100Year
• Operating Supply Voltage (typ): 2.5/3.3/5V
• Package Type: TSSOP
• Operating Temp Range: -40C to 85C
• Supply Current: 3mA
• Operating Supply Voltage (min): 1.8V
• Operating Supply Voltage (max): 5.5V
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

IS24C01B IS24C02B
DEVICE ADDRESSInG
The Master begins a transmission by sending a Start
condition. The Master then sends the address of the
particular Slave devices it is requesting. The Slave device
(Fig. 5) address is 8 bits.
The four most significant bits of the Slave device address
are fixed as 1010 for the IS24C01B/02B.
The next three bits of the Slave address are specific for
each of the EEPROM. The bit values enable access to
multiple memory blocks or multiple devices.
The IS24C01B/02B uses the three bits A0, A1, and A2 in
a comparison with the hard-wired input values on the A0,
A1, and A2 pins. Up to eight units may share the 2-wire
bus.
The last bit of the Slave address specifies whether a Read
or Write operation is to be performed. When this bit is set
to 1, a Read operation is selected, and when set to 0, a
Write operation is selected.
After the Master transmits the Start condition and Slave
address byte (Fig. 5), the appropriate 2-wire Slave (eg.
IS24C02B) will respond with ACK on the SDA line. The
Slave will pull down the SDA on the ninth clock cycle,
signaling that it received the eight bits of data. The selected
EEPROM then prepares for a Read or Write operation by
monitoring the bus.
Integrated Silicon Solution, Inc. — www.issi.com
Rev. F
9/11/09
Page Write
The IS24C01B/02B is capable of 8-byte Page-Write
operation. A Page-Write is initiated in the same manner as
a Byte Write, but instead of terminating the internal Write
cycle after the first data word is transferred, the Master
device can transmit up to 7 more bytes. After the receipt of
each data word, the EEPROM responds immediately with
an ACK on SDA line, and the three lower order data word
address bits are internally incremented by one, while the
higher order bits of the data word address remain constant.
If a byte address is incremented from the last byte of a
page, it returns to the first byte of that page. If the Master
device should transmit more than 8 bytes prior to issuing
the Stop condition, the address counter will “roll over,” and
the previously written data will be overwritten. Once all 8
bytes are received and the Stop condition has been sent by
the Master, the internal programming cycle begins. At this
point, all received data is written to the IS24C01B/02B in a
single Write cycle. All inputs are disabled until completion
of the internal Write cycle.
Acknowledge (ACK) Polling
The disabling of the inputs can be used to take advantage
of the typical Write cycle time. Once the Stop condition
is issued to indicate the end of the host's Write operation,
the IS24C01B/02B initiates the internal Write cycle. ACK
polling can be initiated immediately. This involves issuing
the Start condition followed by the Slave address for a
Write operation. If the EEPROM is still busy with the Write
operation, no ACK will be returned. If the IS24C01B/02B
has completed the Write operation, an ACK will be returned
and the host can then proceed with the next Read or Write
operation.
WRITE OPERATIOn
Byte Write
In the Byte Write mode, the Master device sends the Start
condition and the Slave address information (with the R/W
set to Zero) to the Slave device. After the Slave generates
an ACK, the Master sends the byte address that is to be
written into the address pointer of the IS24C01B/02B. After
receiving another ACK from the Slave, the Master device
transmits the data byte to be written into the address
memory location. The IS24C01B/02B acknowledges
once more and the Master generates the Stop condition,
at which time the device begins its internal programming
cycle. While this internal cycle is in progress, the device
will not respond to any request from the Master device.
7