LTC4007EUFD-1#TRPBF Linear Technology, LTC4007EUFD-1#TRPBF Datasheet - Page 9

• Manufacturer Part Number: LTC4007EUFD-1#TRPBF
• Description: IC CHARGER BATTERY 4A 24-QFN
• Manufacturer: Linear Technology
• Type: Battery Chargerr

Specifications of LTC4007EUFD-1#TRPBF

• Function: Charge Management
• Battery Type: Lithium-Ion (Li-Ion)
• Voltage - Supply: 6 V ~ 28 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 24-WFQFN Exposed Pad
• Output Current: 4A
• Output Voltage: 4.1/4.2V
• Operating Supply Voltage (min): 6V
• Operating Supply Voltage (max): 28V
• Operating Temp Range: -40C to 85C
• Package Type: QFN
• Mounting: Surface Mount
• Pin Count: 24
• Operating Temperature Classification: Industrial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

OPERATIO
Overview
The LTC4007-1 is a synchronous current mode PWM
step-down (buck) switcher battery charger controller. The
charge current is programmed by the combination of a
program resistor (R
and a sense resistor (R
pins. The final float voltage is programmed to one of four
values (12.3V, 12.6V, 16.4V, 16.8V) with ±1% maximum
accuracy using pins 3C4C and CHEM. Charging begins
when the potential at the DCIN pin rises above the voltage
at BAT (and the UVLO voltage) and the SHDN pin is low; the
CHG pin is set low. At the beginning of the charge cycle, if
the cell voltage is below 3.25V (3.173V if CHEM is low), the
LOBAT pin will be low. The LOBAT indicator can be used
to reduce the charging current to a low value, typically
10% of full scale. If the cell voltage stays below 3.25V for
25% of the total charge time, the charge sequence will be
terminated immediately and the FAULT pin will be set low.
An external thermistor network is sampled at regular
intervals. If the thermistor value exceeds design limits,
charging is suspended and the FAULT pin is set low. If the
thermistor value returns to an acceptable value, charging
resumes and the FAULT pin is set high. An external resistor
on the R
defeated by forcing the CHG pin to a low voltage.
As the battery approaches the final float voltage, the
charge current will begin to decrease. When the current
TEST CIRCUIT
T
pin sets the total charge time. The timer can be
U
PROG
SENSE
) from the PROG pin to ground
) between the CSP and BAT
13
5
CHEM
3C4C
11
CSP
DIVIDER/
MUX
12
BAT
V
REF
drops to 10% of the full-scale charge current, an internal
C/10 comparator will indicate this condition by latching
the FLAG pin low. The charge timer is also reset to 1/4 of
the total charge time when FLAG goes low. If this condition
is caused by an input current limit condition, described
below, then the FLAG indicator will be inhibited. When a
time-out occurs, charging is terminated immediately and
the CHG pin is forced to a high impedance state. To restart
the charge cycle manually, simply remove the input volt-
age and reapply it, or set the SHDN pin high momentarily.
When the input voltage is not present, the charger goes
into a sleep mode, dropping battery current drain to 15µA.
This greatly reduces the current drain on the battery and
increases the standby time. The charger is inhibited any
time the SHDN pin is high.
Input FET
The input FET circuit performs two functions. It enables
the charger if the input voltage is higher than the CLN pin
and provides the logic indicator of AC present on the ACP
pin. It controls the gate of the input FET to keep a low
forward voltage drop when charging and also prevents
reverse current flow through the input FET.
If the input voltage is less than V
170mV higher than V
occurs the ACP pin is released and pulled up with an
external load to indicate that the adapter is present. The
+
–
EA
LT1055
+
–
LTC4007-1
8
40071 TC
ITH
CLN
0.6V
to activate the charger. When this
CLN
LTC4007-1
, it must go at least
40071f
9