LM334H/NOPB National Semiconductor, LM334H/NOPB Datasheet - Page 6

• Manufacturer Part Number: LM334H/NOPB
• Description: IC CURRENT SOURCE ADJ TO46-3
• Manufacturer: National Semiconductor

Specifications of LM334H/NOPB

• Function: Current Source
• Accuracy: ±3%
• Voltage - Input: 1 ~ 40 V
• Current - Output: 10mA
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Through Hole
• Package / Case: TO-46-3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Sensing Method: -
• Other names: *LM334H; *LM334H/NOPB; LM334H

www.national.com
Application Hints
regulation by at least an order of magnitude. DC character-
istics (with the exception of minimum input voltage), are not
affected.
NOISE
Current noise generated by the LM134 is approximately 4
times the shot noise of a transistor. If the LM134 is used as
an active load for a transistor amplifier, input referred noise
will be increased by about 12dB. In many cases, this is
acceptable and a single stage amplifier can be built with a
voltage gain exceeding 2000.
LEAD RESISTANCE
The sense voltage which determines operating current of the
LM134 is less than 100mV. At this level, thermocouple or
lead resistance effects should be minimized by locating the
current setting resistor physically close to the device. Sock-
ets should be avoided if possible. It takes only 0.7Ω contact
resistance to reduce output current by 1% at the 1 mA level.
This property of the LM134 is illustrated in the accompanying
graph. Line abc is the sensor current before trimming. Line
a'b'c' is the desired output. A gain trim done at T2 will move
the output from b to b' and will simultaneously correct the
slope so that the output at T1 and T3 will be correct. This
gain trim can be done on R
to terminate the LM134. Slope error after trim will normally
be less than
temperature coefficient resistor must be used for R
A 33 ppm/˚C drift of R
the resistor will normally see about the same temperature
variations as the LM134. Separating R
requires 3 wires and has lead resistance problems, so is not
±
1%. To maintain this accuracy, however, a low
SET
will give a 1% slope error because
SET
(Continued)
or on the load resistor used
SET
from the LM134
FIGURE 2. Gain Adjustment
SET
.
6
SENSING TEMPERATURE
The LM134 makes an ideal remote temperature sensor be-
cause its current mode operation does not lose accuracy
over long wire runs. Output current is directly proportional to
absolute temperature in degrees Kelvin, according to the
following formula:
Calibration of the LM134 is greatly simplified because of the
fact that most of the initial inaccuracy is due to a gain term
(slope error) and not an offset. This means that a calibration
consisting of a gain adjustment only will trim both slope and
zero at the same time. In addition, gain adjustment is a one
point trim because the output of the LM134 extrapolates to
zero at 0˚K, independent of R
normally recommended. Metal film resistors with less than
20 ppm/˚C drift are readily available. Wire wound resistors
may also be used where best stability is required.
APPLICATION AS A ZERO TEMPERATURE
COEFFICENT CURRENT SOURCE
Adding a diode and a resistor to the standard LM134 con-
figuration can cancel the temperature-dependent character-
istic of the LM134. The circuit shown in Figure 3 balances
the positive tempco of the LM134 (about +0.23 mV/˚C) with
the negative tempco of a forward-biased silicon diode (about
−2.5 mV/˚C).
00569704
SET
or any initial inaccuracy.