LTC3411EMS#TRPBF Linear Technology, LTC3411EMS#TRPBF Datasheet - Page 12

• Manufacturer Part Number: LTC3411EMS#TRPBF
• Description: IC CONV DC/DC SYNC STPDWN 10MSOP
• Manufacturer: Linear Technology
• Type: Step-Down (Buck)r

Specifications of LTC3411EMS#TRPBF

• Internal Switch(s): Yes
• Synchronous Rectifier: Yes
• Number Of Outputs: 1
• Voltage - Output: 0.8 ~ 5 V
• Current - Output: 1.25A
• Frequency - Switching: 1MHz
• Voltage - Input: 2.63 ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 10-MSOP, Micro10™, 10-uMAX, 10-uSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Power - Output: -

APPLICATIONS INFORMATION
LTC3411
Ceramic Input and Output Capacitors
Higher value, lower cost ceramic capacitors are now be-
coming available in smaller case sizes. These are tempting
for switching regulator use because of their very low ESR.
Unfortunately, the ESR is so low that it can cause loop
stability problems. Solid tantalum capacitor ESR generates
a loop “zero” at 5kHz to 50kHz that is instrumental in giving
acceptable loop phase margin. Ceramic capacitors remain
capacitive to beyond 300kHz and ususally resonate with
their ESL before ESR becomes effective. Also, ceramic
caps are prone to temperature effects which requires the
designer to check loop stability over the operating tem-
perature range. To minimize their large temperature and
voltage coeffi cients, only X5R or X7R ceramic capacitors
should be used. A good selection of ceramic capacitors
is available from Taiyo Yuden, TDK and Murata.
Great care must be taken when using only ceramic input
and output capacitors. When a ceramic capacitor is used
at the input and the power is being supplied through long
wires, such as from a wall adapter, a load step at the output
can induce ringing at the V
couple to the output and be mistaken as loop instability.
At worst, the ringing at the input can be large enough to
damage the part.
Since the ESR of a ceramic capacitor is so low, the input
and output capacitor must instead fulfi ll a charge storage
requirement. During a load step, the output capacitor must
instantaneously supply the current to support the load
until the feedback loop raises the switch current enough
to support the load. The time required for the feedback
loop to respond is dependent on the compensation com-
ponents and the output capacitor size. Typically, 3 to 4
12
IN
pin. At best, this ringing can
cycles are required to respond to a load step, but only in
the fi rst cycle does the output drop linearly. The output
droop, V
drop of the fi rst cycle. Thus, a good place to start is with
the output capacitor size of approximately:
More capacitance may be required depending on the duty
cycle and load step requirements.
In most applications, the input capacitor is merely required
to supply high frequency bypassing, since the impedance
to the supply is very low. A 10μF ceramic capacitor is
usually enough for these conditions.
Setting the Output Voltage
The LTC3411 develops a 0.8V reference voltage between
the feedback pin, V
Figure 5. The output voltage is set by a resistive divider
according to the following formula:
Keeping the current small (<5μA) in these resistors maxi-
mizes effi ciency, but making them too small may allow
stray capacitance to cause noise problems and reduce the
phase margin of the error amp loop.
To improve the frequency response, a feed-forward capaci-
tor C
route the V
inductor or the SW line.
C
V
OUT
OUT
F
may also be used. Great care should be taken to
DROOP
≈
≈
0 8
FB
2 5 .
.
line away from noise sources, such as the
V
, is usually about 2 to 3 times the linear
f
O
⎛
⎜
⎝
1
•
Δ
FB
+
V
I
OUT
DROOP
, and the signal ground as shown in
R
R
2
1
⎞
⎟
⎠
3411fb