TLE6389G 50-1 Infineon Technologies, TLE6389G 50-1 Datasheet - Page 19

• Manufacturer Part Number: TLE6389G 50-1
• Description: IC CONV DC/DC BUCK PDSO-14
• Manufacturer: Infineon Technologies
• Type: Step-Down (Buck), Step-Up (Boost)r

Specifications of TLE6389G 50-1

• Internal Switch(s): Yes
• Synchronous Rectifier: No
• Number Of Outputs: 1
• Voltage - Output: 5V
• Current - Output: 3A
• Frequency - Switching: 360kHz
• Voltage - Input: 5 ~ 60 V
• Operating Temperature: -40°C ~ 150°C
• Mounting Type: Surface Mount
• Package / Case: DSO-14
• Output Voltage: 5 V
• Output Current: 3 A
• Input Voltage: 5 V to 60 V
• Mounting Style: SMD/SMT
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• For Use With: DEMOBOARDTLE6389-3GV50IN - BOARD DEMO FOR TLE 6389-3 GV50DEMOBOARDTLE6389-2GVIN - BOARD DEMO FOR TLE 6389-2GVDEMOBOARDTLE6389-2GV50IN - BOARD DEMO FOR TLE 6389-2 GV50
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Power - Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: SP000015001; TLE6389G501NT; TLE6389G501T

4.1.3
This control scheme overrides PWM mode and places the TLE6389 in PFM mode at
light loads to improve efficiency and reduce quiescent current to less than 100µA. The
pulse-skipping PFM operation is initiated when the peak inductor current drops below 0.1
x I
reducing the switching frequency and associated losses in the external switch, the
rectifier diode, and the external inductor. During PFM mode, a switching cycle initiates
when the PFM comparator senses that the output voltage has dropped too low. The P-
channel MOSFET switch turns on and conducts current to the output-filter capacitor and
load until the inductor current reaches the PFM peak voltage limit. Then the switch turns
off and the magnetic field in the inductor collapses, forcing current through the
synchronous rectifier to the output filter capacitor and load. Then the TLE6389 waits until
the PFM comparator senses a low output voltage again.
Output ripple is higher during PFM operation. A larger output-filter capacitor can be used
to minimize ripple.
4.2
The TLE6389’s internal oscillator is set for a fixed-switching frequency of 360kHz or can
be synchronized to an external clock. Do not leave SYNC unconnected. Connecting
SYNC to GND enables PWM/PFM operation to reduce supply current at light loads.
SYNC is a negative-edge triggered input that allows synchronization to an external
frequency ranging between 270kHz and 450kHz. When SYNC is clocked by an external
signal, the converter operates in PWM mode until the load current drops below the PWM
to PFM threshold. Thereafter the converter continues operation in PFM mode.
4.3
Connecting ENABLE to GND places the TLE6389GV, TLE6389G33 and TLE6389G50
in shutdown mode. In shutdown, the reference, control circuitry, external switching
MOSFET, and the oscillator are turn off and the output falls to 0V. Connect ENABLE to
IN for normal operation.
4.4
Connecting SI_ENABLE to 5V causes SI_GND to have low impedance. Thus the SI
comparator is operational and ca be used to monitor the battery voltage. SO output
signal is valid. Connecting SI_ENABLE to GND causes SI_GND to have high
impedance. Thus the SI comparator is not able to monitor the battery voltage. SO output
signal is invalid.
Target Datasheet Rev. 1.7
limit
. During PFM operation, the TLE6389 switches only as needed to service the load,
PWM/PFM Operation
SYNC Input and Frequency Control
Shutdown Mode
SI_Enable
19
TLE 6389
2001-09-17