LTL42EKEKNN Lite-On Electronics, LTL42EKEKNN Datasheet
LTL42EKEKNN
Specifications of LTL42EKEKNN
Available stocks
Related parts for LTL42EKEKNN
LTL42EKEKNN Summary of contents
Page 1
... All dimensions are in millimeters (inches). 2. Tolerance is ±0.25mm(.010") unless otherwise noted. 3. Protruded resin under flange is 1.0mm(.04") max. 4. Lead spacing is measured where the leads emerge from the package. 5. Specifications are subject to change without notice. Part No. : LTL42EKEKNN BNS-OD-C131/A4 Lens Source Color Water Clear ...
Page 2
... Parameter Power Dissipation Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width) DC Forward Current Derating Linear From 50℃ Reverse Voltage Operating Temperature Range Storage Temperature Range Lead Soldering Temperature [1.6mm(.063") From Body] Part No. : LTL42EKEKNN BNS-OD-C131/A4 =25℃ A Maximum Rating 0.4 5 -40 ℃ ...
Page 3
... Iv classification code is marked on each packing bag. 4. The dominant wavelength, λd is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. Part No. : LTL42EKEKNN BNS-OD-C131/A4 =25℃ A Symbol Min ...
Page 4
... LITE-ON TECHNOLOGY CORPORATION Typical Electrical / Optical Characteristics Curves (25 ℃ Part No. : LTL42EKEKNN BNS-OD-C131/A4 Ambient Temperature Unless Otherwise Noted) Page : ...
Page 5
... Inner cartons per outer carton total 80000 pcs per outer carton In every shipping lot, only the last pack will be non-full packing Part No. : LTL42EKEKNN BNS-OD-C131/A4 Packing Spec Page : 5 of ...
Page 6
... Bin Code Note: Tolerance of each bin limit is ±15% Dominant Wavelength Bin Code H27 H28 H29 H30 H31 Note: Tolerance of each bin limit is ±1nm Part No. : LTL42EKEKNN BNS-OD-C131/A4 Unit : mcd @20mA Min. Max. 310 520 520 880 880 1500 1500 2500 Unit : nm @20mA Min ...
Page 7
... Soldering time 3 sec. Max. (one time only) Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or catastrophic failure of the LED. IR reflow is not suitable process for through hole type LED lamp product. Part No. : LTL42EKEKNN BNS-OD-C131/A4 CAUTIONS Wave soldering Pre-heat 100° ...
Page 8
... All devices, equipment, and machinery must be properly grounded Work tables, storage racks, etc. should be properly grounded Use ion blower to neutralize the static charge which might have built up on surface of the LEDs plastic lens as a result of friction between LEDs during storage and handing Part No. : LTL42EKEKNN BNS-OD-C131/A4 Circuit model B LED ...
Page 9
... No static charge generators (e.g. plastics) inside shielding containers with ESDS items? 4. All flexible conductive and dissipative package materials inspected before reuse or recycle? Others 1. Audit result reported to entity ESD control coordinator? 2. Corrective action from previous audits completed? 3. Are audit records complete and on file? Part No. : LTL42EKEKNN BNS-OD-C131/A4 Page : ...
Page 10
... Environmental Test Solder Resistance Solderability 9. Others The appearance and specifications of the product may be modified for improvement, without prior notice. Part No. : LTL42EKEKNN BNS-OD-C131/A4 Test Condition Ta= Under Room Temperature As Per Data Sheet Maximum Rating *Test Time= 1000HRS (-24HRS,+72HRS) Ta= 65±5℃ RH= 90 ～ 95% Test Time= 240HRS± ...