JNW350R641-TZ Lineage Power, JNW350R641-TZ Datasheet
JNW350R641-TZ
Specifications of JNW350R641-TZ
CC109149836
Available stocks
Related parts for JNW350R641-TZ
JNW350R641-TZ Summary of contents
Page 1
Data Sheet August 9, 2010 JNW350R Series Power Modules; DC-DC Converters RoHS Compliant Applications RF Power Amplifier Wireless Networks Switching Networks Options Auto-restart after either output OCP or OVP fault shutdown (“3” option code) Auto-restart ...
Page 2
August 9, 2010 Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other ...
Page 3
August 9, 2010 (continued) Electrical Specifications Parameter Output Voltage Set-point ( =25°C) IN IN,nom O O, max c Output Voltage (Over all operating input voltage, resistive load, and temperature conditions until end of life) ...
Page 4
August 9, 2010 Feature Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See Feature Descriptions for additional information. Parameter Remote On/Off Signal Interface ( open collector or equivalent, ...
Page 5
Data Sheet August 9, 2010 Characteristic Curves The following figures provide typical characteristics for the JNW350R (28V, 12.5A) at 25ºC. The figures are identical for either positive or negative Remote On/Off logic Vin=48V Vin=75V Vin=36V 80 75 ...
Page 6
Data Sheet August 9, 2010 Test Configurations Note: Measure the input reflected-ripple current with a simulated source inductance (LTEST µH. Capacitor CS offsets possible battery impedance. Measure the current, as shown above. Figure 7. Input Reflected Ripple Current ...
Page 7
Data Sheet August 9, 2010 Safety Considerations (continued) For all input sources, other than DC MAINS, where the input voltage is between 60 and 75V dc (Classified as TNV-2 in Europe), the following must be meet, if the converter’s output ...
Page 8
Data Sheet August 9, 2010 Feature Description (continued) Remote sense Remote sense minimizes the effects of distribution losses by regulating the voltage at the remote-sense connection (see Figure 11). For No Trim or Trim down application, the voltage between the ...
Page 9
Data Sheet August 9, 2010 Feature Description (continued) The following equation determines the required external-resistor value to obtain a percentage output voltage change of %. For output voltages: 28V 100 %) O ...
Page 10
... Figure 17. The value of R will be dependent on the voltage step and range of G the DAC and the desired values for trim-up and trim- down Please contact your Lineage Power Δ%. technical representative to obtain more details on the selection for this resistor. LINEAGE POWER JNW350R Power Modules ...
Page 11
... Please contact your Lineage Power technical representative to obtain more details of this feature as well as for guidelines on how to select the right value of external R-C to tune the module for best transient performance and stable operation for other output capacitance values. ...
Page 12
... For Pb solder, the recommended pot temperature is 260C, while the Pb-free solder pot is 270C max. Not all RoHS-compliant through-hole products can be processed with paste-through-hole Pb or Pb-free reflow process. If additional information is needed, please consult with your Lineage Power representative for more details. 12 ...
Page 13
Data Sheet August 9, 2010 EMC Considerations The filter circuit schematic and plots in Figure 23 shows a suggested configuration as tested to meet the conducted emission limits of EN55022 Class B. Note: Customer is ultimately responsible for the proper ...
Page 14
Data Sheet August 9, 2010 Mechanical Outline for Through-Hole Module Dimensions are in inches and [millimeters]. Tolerances: x.xx in. 0.02 in. [x.x mm 0.5 mm] (Unless otherwise indicated) x.xxx in 0.010 in. [x.xx mm 0.25 mm] ...
Page 15
Data Sheet August 9, 2010 Recommended Pad Layout for Through Hole Module Dimensions are in inches and [millimeters]. Tolerances: x.xx in. 0.02 in. [x.x mm 0.5 mm] (Unless otherwise indicated) x.xxx in 0.010 in. [x.xx mm ...
Page 16
... JNW350R631-18Z 92% Through hole JNW350R41-18TZ 92% Through hole JNW350R641 92% Through hole JNW350R641Z 92% Through hole JNW350R641-18 92% Through hole JNW350R641-TZ 92% Through hole JNW350R64-18Z 92% Through hole JNW350R641-18Z 92% Through hole JNW350R841-18TZ Asia-Pacific Headquarters Tel: +65 6593 7211 Europe, Middle-East and Africa Headquarters Tel: +49 89 878067-280 India Headquarters Tel: +91 80 28411633 ...