CC025ACL-M Lineage Power, CC025ACL-M Datasheet - Page 11

• Manufacturer Part Number: CC025ACL-M
• Description: CONV DC/DC +5/+-15V 25W OUT
• Manufacturer: Lineage Power
• Series: CC025r
• Type: Isolatedr

Specifications of CC025ACL-M

• Output: 5V, ±15V
• Number Of Outputs: 3
• Power (watts): 25W
• Mounting Type: Through Hole
• Voltage - Input: 18 ~ 36V
• Package / Case: 10-DIP Module
• 1st Output: 5 VDC @ 5A
• 2nd Output: 15 VDC @ 830mA
• 3rd Output: -15 VDC @ 830mA
• Size / Dimension: 2.80" L x 2.40" W x 0.50" H (71.1mm x 61mm x 12.7mm)
• Power (watts) - Rated: 25W
• Operating Temperature: -40°C ~ 100°C
• Efficiency: 82%
• Approvals: CSA, UL, VDE
• Product: Isolated
• Output Power: 25 W
• Input Voltage Range: 18 V to 36 V
• Output Voltage (channel 1): 5 V
• Output Current (channel 1): 5 A
• Output Voltage (channel 2): 15 V
• Output Current (channel 2): 0.83 A
• Output Voltage (channel 3): - 15 V
• Output Current (channel 3): 0.83 A
• Isolation Voltage: 500 V
• Package / Case Size: DIP
• Output Type: Isolated
• Output Voltage: 5 V
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• 4th Output: -
• Lead Free Status / Rohs Status: No

March 2008
Test Configurations
Figure 19. Output Noise Measurement Test Setup
Figure 20. Triple Output Voltage and Efficiency
Lineage Power
Note: Use the specified ceramic capacitor. Scope measurement
Note: All measurements are taken at the module terminals. When
socketing, place Kelvin connections at module terminals to
avoid measurement errors due to socket contact resistance.
should be made by using a BNC socket. Position the load
between 50 mm (2 in.) and 75 mm (3 in.) from the
module.
η
Measurement Test Setup
=
j
------------------------------------------------------ -
∑
=
3
[
1
V
[
I
+ ( )
V
O j
+ ( )
+
– (
–
(continued)
V
V
I
– ( )
C O M
)
]
]
I
I
I
Oj
×
100
8-810(C).c
8-749(C).c
Design Considerations
Input Source Impedance
The power module should be connected to a low
ac-impedance input source. Highly inductive source im-
pedances can affect the stability of the power module. A
33 µF electrolytic capacitor (ESR < 0.7 ¾ at 100 kHz)
mounted close to the power module helps to ensure
the stability of the unit.
Safety Considerations
For safety-agency approval of the system in which the
power module is used, the power module must be
installed in compliance with the spacing and separation
requirements of the end-use safety agency standard,
i.e., UL-1950, CSA 22.2-950, and EN60950.
For the converter output to be considered meeting the
requirements of safety extra-low voltage (SELV), the
input must meet SELV requirements.
If the input meets extra-low voltage (ELV) require-
ments, then the converter’s output is considered ELV.
The input to these units is to be provided with a maxi-
mum 5 A normal-blow fuse in the ungrounded lead.
18 Vdc to 36 Vdc Input; 25 W
11