ATA016A0X3-SRZ Lineage Power, ATA016A0X3-SRZ Datasheet - Page 14

• Manufacturer Part Number: ATA016A0X3-SRZ
• Description: CONVER DC/DC 0.75 5.5V @ 16A SMD
• Manufacturer: Lineage Power
• Series: Austin SuperLynx™ IIr
• Type: Point of Load (POL) Non-Isolated with Remote On/Offr

Specifications of ATA016A0X3-SRZ

• Output: 0.75 ~ 5.5V
• Number Of Outputs: 1
• Power (watts): 88W
• Mounting Type: Surface Mount
• Voltage - Input: 8.3 ~ 14V
• Package / Case: 7-SMD Module
• 1st Output: 0.75 ~ 5.5 VDC @ 16A
• Size / Dimension: 1.30" L x 0.53" W x 0.33" H (33mm x 13.5mm x 8.3mm)
• Power (watts) - Rated: 88W
• Operating Temperature: -40°C ~ 85°C
• Efficiency: 92%
• Approvals: CSA, EN, UL, VDE
• Output Power: 88 W
• Input Voltage Range: 8.3 V to 14 V
• Output Voltage (channel 1): 0.75 V to 5.5 V
• Output Current (channel 1): 16 A
• Package / Case Size: SMD
• Output Type: Non-Isolated
• Output Voltage: 0.75 V to 5.5 V
• Product: Non-Isolated / POL
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 555-1085-2; CC109104527

Data Sheet
October 1, 2009
Feature Descriptions
Voltage Sequencing
Austin SuperLynx
sequencing feature, EZ-SEQUENCE
users to implement various types of output voltage
sequencing in their applications. This is accomplished
via an additional sequencing pin. When not using the
sequencing feature, either tie the SEQ pin to V
it unconnected.
When an analog voltage is applied to the SEQ pin, the
output voltage tracks this voltage until the output
reaches the set-point voltage. The SEQ voltage must be
set higher than the set-point voltage of the module. The
output voltage follows the voltage on the SEQ pin on a
one-to-one volt basis. By connecting multiple modules
together, customers can get multiple modules to track
their output voltages to the voltage applied on the SEQ
pin.
For proper voltage sequencing, first, input voltage is
applied to the module. The On/Off pin of the module is
left unconnected (or tied to GND for negative logic
modules or tied to V
the module is ON by default. After applying input
voltage to the module, a minimum of 10msec delay is
required before applying voltage on the SEQ pin. During
this time, potential of 50mV (± 10 mV) is maintained on
the SEQ pin.
applied to the SEQ pin and the output voltage of the
module will track this voltage on a one-to-one volt bases
until output reaches the set-point voltage. To initiate
simultaneous shutdown of the modules, the SEQ pin
voltage is lowered in a controlled manner. Output
voltage of the modules tracks the voltages below their
set-point voltages on a one-to-one basis. A valid input
voltage must be maintained until the tracking and output
voltages reach ground potential to ensure a controlled
shutdown of the modules.
When using the EZ-SEQUENCE
start-up of the module, pre-bias immunity feature during
start-up is disabled. The pre-bias immunity feature of
the module relies on the module being in the diode-
mode during start-up. When using the EZ-
SEQUENCE
internal set-up time of 10msec, and will be in
synchronous rectification mode when voltage at the SEQ
pin is applied. This will result in sinking current in the
module if pre-bias voltage is present at the output of the
module. When pre-bias immunity during start-up is
required, the EZ-SEQUENCE
disabled. For additional guidelines on using EZ-
SEQUENCE
contact Lineage Power technical representative for
preliminary application note on output voltage
sequencing using Austin Lynx II series.
LINEAGE
POWER
TM
TM
After 10msec delay, an analog voltage is
feature, modules goes through an
feature of Austin SuperLynx
TM
IN
II 12V series of modules include a
for positive logic modules) so that
TM
(continued)
feature must be
TM
8.3 – 14Vdc Input; 0.75Vdc to 5.5Vdc Output;16A output current
feature to control
TM
Austin SuperLynx
that enables
TM
II 12V,
IN
or leave
Remote Sense
The Austin SuperLynx
have a Remote Sense feature to minimize the effects of
distribution losses by regulating the voltage at the
Remote Sense pin (See Figure 31). The voltage
between the Sense pin and Vo pin must not exceed
0.5V.
The amount of power delivered by the module is defined
as the output voltage multiplied by the output current (Vo
x Io). When using Remote Sense, the output voltage of
the module can increase, which if the same output is
maintained, increases the power output by the module.
Make sure that the maximum output power of the
module remains at or below the maximum rated power.
When the Remote Sense feature is not being used,
connect the Remote Sense pin to output pin of the
module
Figure 31. Remote sense circuit configuration.
TM
R
R
II 12V SMT Non-isolated Power Modules:
distribution
distribution
.
R
R
contact
contact
V
COM
IN
(+)
TM
II 12V SMT power modules
Sense
COM
V
O
R
R
contact
contact
R
R
distribution
distribution
R
LOAD
14