LTM4615EV#PBF Linear Technology, LTM4615EV#PBF Datasheet - Page 8

• Manufacturer Part Number: LTM4615EV#PBF
• Description: IC SWIT REG BUCK 4A ADJ 144LGA
• Manufacturer: Linear Technology
• Series: µModuler
• Type: Point of Load (POL) Non-Isolatedr

Specifications of LTM4615EV#PBF

• Design Resources: LTM4615 Spice Model
• Output: 0.8 ~ 5 V
• Number Of Outputs: 3
• Power (watts): 12W
• Mounting Type: Surface Mount
• Voltage - Input: 2.38 ~ 5.5 V
• Package / Case: 144-LGA
• 1st Output: 0.8 ~ 5 VDC @ 4A
• 2nd Output: 0.8 ~ 5 VDC @ 4A
• 3rd Output: 0.8 ~ 5 VDC @ 4A
• Size / Dimension: 0.59" L x 0.59" W x 0.11" H (15mm x 15mm x 2.8mm)
• Power (watts) - Rated: 12W
• Operating Temperature: -40°C ~ 125°C
• Efficiency: 95%
• Primary Input Voltage: 5.5V
• No. Of Outputs: 3
• Output Voltage: 5V
• Output Current: 1.5A
• Voltage Regulator Case Style: LGA
• No. Of Pins: 144
• Operating Temperature Range: -40°C To +125°C
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIN FUNCTIONS
LTM4615
V
Pins. Apply input voltage between these pins and GND
pins. Recommend placing input decoupling capacitance
directly between V
V
D9-D12, E11-E12): Power Output Pins. Apply output load
between these pins and GND pins. Recommend placing
output decoupling capacitance directly between these pins
and GND pins. Review Table 4.
GND1, GND2, (H1, H7-H12, J6-J12, K6-K8 L1, L7-L8,
M1-M8); (A1-A12, B1, B7-B12, C7-C8, D6-D8, E1,
E8-E10): Power Ground Pins for Both Input and Output
Returns.
TRACK1, TRACK2 (L3, E3): Output Voltage Tracking Pins.
When the module is confi gured as a master output, then a
soft-start capacitor is placed on the RUN/SS pin to ground
to control the master ramp rate, or an external ramp can
be applied to the master regulator’s track pin to control it.
Slave operation is performed by putting a resistor divider
from the master output to the ground, and connecting the
center point of the divider to this pin on the slave regulator.
If tracking is not desired, then connect the TRACK pin to
V
Applications Information section.
FB1, FB2 (L6, E6): The Negative Input of the Switching
Regulators’ Error Amplifi er. Internally, these pins are con-
nected to V
output voltages can be programmed with an additional
resistor between the FB and GND pins. Two power modules
can current share when this pin is connected in parallel
with the adjacent module’s FB pin. See the Applications
Information section.
FB3 (F6): The Negative Input of the LDO Error Amplifi er.
Internally the pin is connected to LDO_OUT with a 4.99k
resistor. Different output voltages can be programmed with
an additional resistor between the FB3 and GND pins. See
the Applications Information section.
8
IN1
OUT1
IN
. Load current must be present for tracking. See the
, V
, V
IN2
OUT2
(J1-J5, K1-K5); (C1-C6, D1-D5): Power Input
OUT
(K9-K12, L9-L12, M9-M12); (C9-C12,
with a 4.99k precision resistor. Different
IN
pins and GND pins.
COMP1, COMP2 (L5, E5): Current Control Threshold
and Error Amplifi er Compensation Point. The current
comparator threshold increases with this control voltage.
Two power modules can current share when this pin is
connected in parallel with the adjacent module’s COMP
pin. Each channel has been internally compensated. See
the Applications Information section.
PGOOD1, PGOOD2 (L4, E4): Output Voltage Power
Good Indicator. Open-drain logic output that is pulled to
ground when the output voltage is not within ±7.5% of
the regulation point.
RUN/SS1, RUN/SS2 (L2, E2): Run Control and Soft-Start
Pin. A voltage above 0.8V will turn on the module, and below
0.5V will turn off the module. This pin has a 1M resistor to
V
Information section for soft-start information.
SW1, SW2 (H2-H6, B2-B6): The switching node of the
circuit is used for testing purposes. This can be connected to
copper on the board for improved thermal performance.
LDO_IN (G1-G4): VLDO Input Power Pins. Place input
capacitor close to these pins.
LDO_OUT (G9-G12): VLDO Output Power Pins. Place
output capacitor close to these pins. Minimum 1mA load
is necessary for proper output voltage accuracy.
BOOST3 (E7): Boost Supply for Driving the Internal VLDO
NMOS Into Full Enhancement. The pin is use for testing
the internal boost converter. The output is typically 5V.
GND3 (F1-F5, F7, F9-F12, G6-G8): The power ground pins
for both input and output returns for the internal VLDO.
PGOOD3 (G5): VLDO Power Good Pin.
EN3 (F8): VLDO Enable Pin.
IN
and a 1000pF capacitor to GND. See the Applications
4615f