HS1650ECN61H Renesas Electronics America, HS1650ECN61H Datasheet

Page 1

To our customers, Old Company Name in Catalogs and Other Documents st On April 1 , 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the ...

Page 2

All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm ...

Page 3

... H8SX/1650 Series E6000H TFP-120 User System Interface Board User’s Manual HS1650ECN61H Rev.3.0 2003.10 ...

Page 4

Cautions Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may ...

Page 5

IMPORTANT INFORMATION • READ this user's manual before using this user system interface board. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interface board until you fully understand its mechanism. User ...

Page 6

LIMITED WARRANTY Renesas warrants its user system interface boards to be manufactured in accordance with published specifications and free from defects in material and/or workmanship. Renesas will repair or replace any user system interface boards determined to be defective in ...

Page 7

State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and ...

Page 8

READ this user's manual before using this user system interface board. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interface board until you fully understand its mechanism. DEFINITION OF SIGNAL ...

Page 9

Observe the precautions listed below. Failure will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST not ...

Page 10

... The HS1650ECN61H is a user system interface board that connects a user system for the H8SX/1650 Series TFP-120 package to the H8SX/1650 Series E6000H emulator (HS1650EPH60H). Preface i ...

Page 11

Section 1 Configuration.....................................................................................1 Section 2 Connection Procedures ......................................................................3 2.1 Connecting User System Interface Board to User System ................................................ 3 2.1.1 Installing IC Socket.............................................................................................. 3 2.1.2 Soldering IC Socket ............................................................................................. 3 2.1.3 Installing IC Socket.............................................................................................. 4 2.1.4 Fastening IC Socket Connector............................................................................ ...

Page 12

Figure 1 and table 1 show the configuration and components of the user system interface board for the TFP-120 package. Please make sure you have all of these components when unpacking. Screws (M2 8 mm) with flat washers Socket cover ...

Page 13

... User’s manual 2 CAUTION Quantity Remarks 1 1 For the TFP-120 package (to be mounted on the user system) 1 For installing an TFP-120-packaged MCU 4 For fastening cable head (with four flat washers) 4 For installing an TFP-120-packaged MCU (with four flat washers) 1 User’s manual for HS1650ECN61H (this manual) ...

Page 14

Section 2 Connection Procedures 2.1 Connecting User System Interface Board to User System Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected to or removed from any part. Before connecting, make ...

Page 15

Installing IC Socket Check the location of pin 1 before inserting. After checking the location of pin 1 on the user system interface board and pin 1 on the IC socket connector, align the guide pins on the IC ...

Page 16

User system Figure 2 Connecting User System Interface Board to User System Screws (M2 12 mm) with flat washers (for fastening cable head) Board Pin 1 IC socket (IC149-120-043-B51 manufactured by YAMAICHI ELECTRONICS Co., Ltd.) 5 ...

Page 17

Exchanging the Spacer of the EV-Chip Board While the user system interface board is connected to the user system, be careful not to apply load. Exchange the spacer (2.6MP mm) provided for the user system interface board ...

Page 18

Connecting User System Interface Board to EV-Chip Board Observe the precautions listed below. Failure will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. ...

Page 19

Figure 4 Connecting User System Interface Board to EV-Chip Board 8 EV-chip board Connector No. Board EV-Chip Board Board Connector No. Connector No. UCN1 UCN1 UCN2 UCN2 ...

Page 20

Recommended Dimensions for User System Mount Pad (Footprint) Figure 5 shows the recommended dimensions for the mount pad (footprint) for the user system with an IC socket for a TFP-120 package (IC149-120-043-B51: manufactured by YAMAICHI ELECTRONICS Co., Ltd). Note ...

Page 21

Dimensions for EV-Chip Board and User System Interface Board The dimensions for the EV-chip board and the user system interface board are shown in figure 6. Figure 6 Dimensions for EV-Chip Board and User System Interface Board 10 140.0 ...

Page 22

Resulting Dimensions after Connecting User System Interface Board The resulting dimensions, after connecting the user system interface board to the user system, are shown in figure 7. SPACER ( 5.8) Figure 7 Resulting Dimensions after Connecting User System Interface ...

Page 23

Section 3 Verifying Operation 1. Turn on the emulator according to the procedures described in the H8SX/1650 Series E6000H Emulator User's Manual (HS1650EPH60HE). 2. Verify the user system interface cable connections by checking the pin states with the CHECK command ...

Page 24

To use the crystal oscillator mounted on the EV-chip board Install the crystal oscillator into the crystal oscillator terminals on the EV-chip board. Crystal oscillator terminals Figure 9 Installing the Clock Oscillator Enlarged view Crystal oscillator X1 X2 Evaluation chip ...

Page 25

Before connecting any parts or cables, make sure that pin 1 on the both sides are correctly aligned not apply excessive force to the user system interface board while it is connected to the user system. 3. ...

Page 26

H8SX/1650 Series E6000H TFP-120 User System Interface Board User's Manual Publication Date: Rev.3.00, October 6, 2003 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Technical Documentation & Information Department Renesas Kodaira Semiconductor Co., Ltd. 2003 Renesas Technology ...

Page 27

H8SX/1650 Series E6000H TFP-120 User System Interface Board 1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 Japan User’s Manual REJ10B0048-0300H ...