DS16EV51-AEVKH National Semiconductor, DS16EV51-AEVKH Datasheet
DS16EV51-AEVKH
Specifications of DS16EV51-AEVKH
Related parts for DS16EV51-AEVKH
DS16EV51-AEVKH Summary of contents
Page 1
... DS16EV5110 features a signal detector with programmable thresholds. The threshold is adjustable through a System Management Bus (SMBus) interface. The DS16EV5110 also provides support for system power management via output enable controls. Additional controls are provided via the SMBus enabling customization and op- timization for specific applications requirements ...
Page 2
Pin Descriptions Pin Name Pin Number I/O, Type HIGH SPEED DIFFERENTIAL I/O C_IN− CML C_IN+ 2 D_IN0− CML D_IN0+ 5 D_IN1− CML D_IN1+ 9 D_IN2− CML D_IN2+ 12 C_OUT CML ...
Page 3
... Connection Diagram TOP VIEW — Not to Scale NSID DS16EV5110SQ DS16EV5110SQX Ordering Information Tape & Reel Quantity 250 2,500 3 20216252 Package SQA48D SQA48D www.national.com ...
Page 4
... Absolute Maximum Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage ( LVCMOS Input Voltage LVCMOS Output Voltage CML Input/Output Voltage Junction Temperature Storage Temperature Lead Temp. (Soldering, 5 sec.) Electrical Characteristics Over recommended operating supply and temperature ranges unless other specified ...
Page 5
Symbol Parameter t Latency D OUTPUT JITTER TJ1 Total Jitter at 1.65 Gbps TJ2 Total Jitter at 2.25 Gbps TJ3 Total Jitter at 165 MHz TJ4 Total Jitter at 225 MHz RJ Random Jitter BIT RATE F Clock Frequency CLK ...
Page 6
Electrical Characteristics — System Management Bus Interface Over recommended operating supply and temperature ranges unless other specified. Symbol Parameter System Bus Interface — DC Specifications V Data, Clock Input Low Voltage IL V Data, Clock Input High Voltage IH I ...
Page 7
Timing Diagrams FIGURE 2. Test Setup Diagram for Jitter Measurement FIGURE 1. SMBus Timing Diagram 7 20216250 20216227 www.national.com ...
Page 8
... When communication to other devices on the SMBus is active, the CS signal for the DS16EV5110s must be driven Low. The address byte for all DS16EV5110s is AC'h. Based on the SMBus 2.0 specification, the DS16EV5110 has a 7-bit slave address of 1010110'b. The LSB is set to 0'b (for a WRITE), thus the 8-bit value is 1010 1100 'b or AC'h ...
Page 9
Name Address Default Type Bit 7 0x00 0x00 RO Status 0x01 0x00 RO Status Status 0x02 0x00 RO Internal 0x03 0x77 RW Enable/ Individual Channel Boost Control for C_IN±, D_IN0± Individual 0x04 0x77 RW Channel Boost Control for D_IN1±, D_IN2± ...
Page 10
... ACTIVE state and all device DS16EV5110 can also be placed in STANDBY mode to save power. In this mode only the control interface including the SMBus port as well as the clock channel signal detection cir- cuit remain active. TABLE 3. Enable and Device State Control ...
Page 11
... AUTOMATIC ENABLE FEATURE It may be desired for the DS16EV5110 to be configured to automatically enter STANDBY mode if no clock signal is FIGURE 3. DS16EV5110 Data Channel FIGURE 4. DS16EV5110 Clock Channel present. STANDBY mode can be implemented by connecting the Signal Detect (SD) pin to the external (LVCMOS) Enable (EN) pin. In order for this option to function properly, REG07[0] should be set to a “ ...
Page 12
... The DS16EV5110 CML outputs will not meet the VOFF parameter required by the HDMI Compliance Test Specification (v1.3b) when the DS16EV5110 is powered off and the sink device is powered FIGURE 6. DS16EV5110 Repeater Application with CAT 5 cable DVI 1.0 AND HDMI V1.2a APPLICATIONS ...
Page 13
... Gbps operation. 20216228 DC COUPLED DATA PATHS AND DVI/HDMI COMPLIANCE The DS16EV5110 is designed to support TMDS differential pairs with DC coupled transmission lines. It contains integrat- ed termination resistors (50Ω), pulled up to VDD at the input stage, and open collector outputs for DVI / HDMI for signal swing ...
Page 14
... Over 28 AWG DVI/HDMI Cable www.national.com UTP (UNSHIELDED TWIST PAIRS) CABLES The DS16EV5110 can be used to extend the length of UTP cables, such as Cat5, Cat5e and Cat6 to distances greater than 20 meters at 1.65 Gbps with < 0. jitter. Please note that for non-standard DVI/HDMI cables, the user must ensure the clock-to-data channel skew requirements are met ...
Page 15
... These capac- itors can be either tantalum or an ultra-low ESR ceramic and should be placed as close as possible to the DS16EV5110. EQUIVALENT I/O STRUCTURES Figure 10 shows the DS16EV5110 CML output structure and ESD protection circuitry ...
Page 16
Typical Performance Characteristics FIGURE 12. Un-equalized vs. Equalized Signal after 25m of 28 AWG DVI Cable at 1.65 Gbps (0x06 Setting) FIGURE 13. Output Signal after 20m of Cat5 Cable at 1.65 Gbps (0x06 Setting) FIGURE 14. Output Signal after ...
Page 17
FIGURE 15. Output Signal after 0. AWG DVI Cable at 1.65 Gbps (0x04 Setting) FIGURE 16. Output Signal after 20m of 28 AWG HDMI Cable at 2.25 Gbps (0x06 Setting) 20216233 20216234 17 www.national.com ...
Page 18
... To order lead-free products, call your National Semiconductor distributors. They can order products for you with an "NOPB" specification. For more information on our Lead-free program, please check out our Lead-Free Status page. www.national.com inches (millimeters) unless otherwise noted 7mm x 7mm 48-pin LLP Package Order Number DS16EV5110SQ Package Number SQA48D 18 ...
Page 19
Notes 19 www.national.com ...
Page 20
... For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Amplifiers www.national.com/amplifiers Audio www.national.com/audio Clock Conditioners www.national.com/timing Data Converters www.national.com/adc Displays www.national.com/displays Ethernet www.national.com/ethernet Interface www.national.com/interface LVDS www.national.com/lvds Power Management www.national.com/power Switching Regulators www.national.com/switchers LDOs www ...