LM2735YSDEVAL National Semiconductor, LM2735YSDEVAL Datasheet
LM2735YSDEVAL
Manufacturer Part Number
LM2735YSDEVAL
Description
BOARD EVAL LM2735 520KHZ 6LLP
Manufacturer
National Semiconductor
Specifications of LM2735YSDEVAL
Main Purpose
DC/DC, Step Up
Outputs And Type
1, Non-Isolated
Voltage - Output
12V
Current - Output
500mA
Voltage - Input
3 ~ 5.5V
Regulator Topology
Boost
Frequency - Switching
520kHz
Board Type
Fully Populated
Utilized Ic / Part
LM2735
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power - Output
-
© 2007 National Semiconductor Corporation
LM2735Y 6-Pin LLP Demo
Board
Introduction
The demo board included in this shipment converts 3V to 5.5V
input to 12V output for up to 500mA load current using the
LM2735Y 520kHz DC-DC switching converter. This is a 2-
layer board using the bottom layer as a Ground plane.
A bill of materials below describes the parts used on this demo
board. A schematic and layout have also been included below
Pin Description for 6-Pin LLP
DAP
Pin
1
2
3
4
5
6
PGND
AGND
Name
GND
VIN
SW
EN
FB
300258
Function
Power ground pin. Place PGND and output capacitor GND close together.
Supply voltage for power stage, and Input supply voltage.
Shutdown control input. Logic high enables operation. Do not allow this pin to float
or be greater than VIN + 0.3V.
Feedback pin. Connect FB to external resistor divider to set output voltage.
Signal ground pin. Place the bottom resistor of the feedback network as close as
possible to pin 5
Output switch. Connect to the inductor, output diode.
Signal & Power ground. Connect to pin 1 & pin 5 on top layer. Place 4-6 via’s from
DAP to bottom layer GND plane.
LM2735Y 6-Pin LLP Schematic
Top View
Pin-Out
National Semiconductor
Application Note 1660
Matthew Reynolds
June 2007
along with measured performance characteristics. The above
restrictions for the input voltage are valid only for the demo
board as shipped with the demo board schematic below.
Operating Conditions
V
V
I
O
IN
O
= 500mA
= 12V
= 3V to 5.5V
30025802
30025801
www.national.com
Related parts for LM2735YSDEVAL
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
National Semiconductor [8-Bit D/A Converter]
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
National Semiconductor [Media Coprocessor]
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Digitally Controlled Tone and Volume Circuit with Stereo Audio Power Amplifier, Microphone Preamp Stage and National 3D Sound
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Digitally Controlled Tone and Volume Circuit with Stereo Audio Power Amplifier, Microphone Preamp Stage and National 3D Sound
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
AC97 Rev 2 Codec with Sample Rate Conversion and National 3D Sound
Manufacturer:
National Semiconductor
Part Number:
Description:
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
General Purpose, Low Voltage, Low Power, Rail-to-Rail Output Operational Amplifiers
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
8-bit 20 MSPS flash A/D converter.
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Low Noise Quad Operational Amplifier
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Quad Differential Line Receivers
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Quad High Speed Trapezoidal? Bus Transceiver
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Dual Line Receiver
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
TTL to 10k ECL Level Translator with Latch
Manufacturer:
National Semiconductor
Datasheet:
LM2735YSDEVAL Summary of contents
Page 1
... FB 5 AGND 6 SW DAP GND © 2007 National Semiconductor Corporation National Semiconductor Application Note 1660 Matthew Reynolds June 2007 along with measured performance characteristics. The above restrictions for the input voltage are valid only for the demo board as shipped with the demo board schematic below. ...
Page 2
Bill of Materials LM2735Y Part Input Cap C5 Input Cap C3 Output Cap C4 Output Cap C2 Comp Cap D1, Catch Diode 0. www.national.com Part Value Manufacturer 2.1A Boost Regulator 22µF, 6.3V, X5R ...
Page 3
PCB Layout 30025804 Top Layer 30025805 Bottom Layer 3 www.national.com ...
Page 4
... National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. ...