LP38513S-1.8EV National Semiconductor, LP38513S-1.8EV Datasheet
LP38513S-1.8EV
Specifications of LP38513S-1.8EV
Related parts for LP38513S-1.8EV
LP38513S-1.8EV Summary of contents
Page 1
... ERROR Flag: The ERROR Flag goes low if V than typically 15% below the nominal value. Precision Output Voltage: A guaranteed V ±2.6% with T from 0°C to 125°C. J Typical Application Circuit © 2009 National Semiconductor Corporation LP38513-1.8 Features ■ Conversions from 2.5V rail to 1.8V ■ Stable with ceramic capacitors ■ ...
Page 2
... The TO220 and TO263 TAB is used as a thermal connection to remove heat from the device to an external heatsink. The TAB is internally connected to device pin 3. 2 Package Marking Supplied As: LP38513S-1.8 Rail LP38513S-1.8 Tape and Reel LP38513T-1.8 Rail 20146804 Top View TO-263 5 Pin Package ...
Page 3
... Absolute Maximum Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Storage Temperature Range Soldering Temperature (Note 3) TO-220, Wave TO-263 ESD Rating (Note 2) Power Dissipation (Note 4) Input Pin Voltage (Survival) Enable Pin Voltage (Survival) ...
Page 4
Symbol Parameter ERROR Flag ERROR Flag Threshold V TH (Note 9) ERROR Flag Threshold ΔV Hysteresis TH (Note 9) ERROR Flag Saturation V ERROR(SAT) Voltage ERROR Flag Pin Leakage I lk Current t ERROR Flag Delay time d AC Parameters ...
Page 5
Typical Performance Characteristics µ µ mA. IN OUT OUT V vs Temperature OUT Ground Pin Current (I GND Ground Pin Current Temperature GND Unless otherwise specified: T 20146811 ) ...
Page 6
OUT ERROR Flag Low vs Temperature Load regulation vs Temperature www.national.com V EN OUT 20146832 20146818 20146820 6 ERROR Flag Threshold vs Temperature 20146817 ERROR Flag Leakage vs Temperature 20146819 Line Regulation vs Temperature 20146821 ...
Page 7
Current Limit vs Temperature Load Transient 3A μF Ceramic + 100 μF Aluminum C OUT Load Transient μF Ceramic + 100 μF Aluminum C OUT Load Transient 10mA to 3A, ...
Page 8
PSRR www.national.com 20146829 8 Noise 20146831 ...
Page 9
Block Diagram Application Information EXTERNAL CAPACITORS Like any low-dropout regulator, external capacitors are re- quired to assure stability. These capacitors must be correctly selected for proper performance. INPUT CAPACITOR: A ceramic input capacitor of at least 10 µF is required. ...
Page 10
Please refer to the POW- ER DISSIPATION/HEAT-SINKING section for power dissi- pation calculations. ENABLE OPERATION The Enable On/Off threshold is typically 850 mV, and has no hysteresis. The voltage signal must rise and fall ...
Page 11
FIGURE 2. ERROR Flag Operation, biased from V POWER DISSIPATION/HEAT-SINKING A heat-sink may be required depending on the maximum power dissipation (P ), maximum ambient temperature D(MAX) (T )of the application, and the thermal resistance (θ A(MAX) the package. Under ...
Page 12
FIGURE 3. θ vs Copper (1 Ounce) Area for the TO-263 JA package As shown in the figure, increasing the copper area beyond 1 square inch produces very little improvement. The minimum value for θ for the TO-263 package mounted ...
Page 13
Physical Dimensions inches (millimeters) unless otherwise noted TO263 5-Lead, Molded, Surface Mount Package TO220 5-lead, Molded, Stagger Bend Package NS Package Number T05D NS Package Number TS5B 13 www.national.com ...
Page 14
... For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Amplifiers www.national.com/amplifiers Audio www.national.com/audio Clock and Timing www.national.com/timing Data Converters www.national.com/adc Interface www.national.com/interface LVDS www.national.com/lvds Power Management www.national.com/power Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www ...