EDK2398 Renesas Electronics America, EDK2398 Datasheet

Page 1

... EDK2398 U M SER ANUAL F H8S/2398 FLASH M N CHIP ICROCONTROLLER ...

Page 2

Preface Cautions 1. This document may be, wholly or partially, subject to change without notice. 2. All rights reserved. No one is permitted to reproduce or duplicate, in any form, a part or this entire document without Hitachi Micro Systems ...

Page 3

T C ABLE OF ONTENTS ............................................................................................................................................. 3 ABLE OF ONTENTS ....................................................................................................................................... 4 TART UP NSTRUCTIONS 2.1. INSTALLING THE EVALUATION DEVELOPMENT KIT (EDK)........................................................................... 4 2.2. SERIAL CONNECTION ....................................................................................................................................... 4 2.3. POWER SUPPLY ................................................................................................................................................ ...

Page 4

TART UP NSTRUCTIONS 2. NSTALLING THE VALUATION Please refer to the quick start guide provided for initial installation of the EDK. A copy of the quick start guide and other information relating to this ...

Page 5

EDK B L OARD AYOUT The diagram shows a general layout of the EDK board. FLASH Programming Power NMI Switch BOOT LED Power LED User1 LED User2 LED RESET BOOT Switch Switch CJ5 9-Way D-Type CJ4 3.1. EDK B ...

Page 6

EDK O PERATION 4. SER NTERFACE The EDK provides three buttons for influencing the operation of the board. The purpose of each button is clearly marked next to it. Refer to the board layout for positions (Section ...

Page 7

C C RYSTAL HOICE The operating crystal frequency has been chosen to support the fastest operation with the fastest serial operating speeds. The value of the crystal is 18.432MHz. The following table shows the baud rates and Baud Rate ...

Page 8

M M EMORY AP Table 4-4 illustrates the EDK memory map for mode 6. Section Start Section End H’000000 H’00FFFF H’010000 H’03FFFF H’040000 H’3FFFFF H’400000 H’43FFFF H’440000 H’FFDBFF H’FFDC00 H’FFFBFF H’FFFC00 H’FFFE3F H’FFFE40 H’FFFF07 H’FFFF08 H’FFFF27 H’FFFF28 H’FFFFFF 4.5. ...

Page 9

B O OARD PTIONS The EDK has a number of configuration settings set by jumpers CJ4 ( CJ5 ( and zero-ohm links. Common EDK functions can be set using the jumpers as described ...

Page 10

– CJ5 SER ODE ETTINGS CJ5 is used to set the operating mode of the microcontroller. These jumpers must be fitted at all times to ensure correct operation of the EDK. Jumper CJ 5-A User Mode ...

Page 11

ERIAL ORT ELECTION The programming serial port is connected to the RS232 connector by default. This allows direct programming of the EDK using the supplied software tools. A secondary serial port is available on the microcontroller ...

Page 12

... E10A H EADER E10A/E10T is not supported on the EDK2398 5. OOT ONTROL The method for placing the microcontroller device in to Boot mode for reprogramming has been incorporated into a complex programmable logic device (CPLD). This is not necessary for most user designs but allows a measure of increased flexibility for the EDK designs ...

Page 13

C D ODE EVELOPMENT 6.1. HMON 6.1. ODE UPPORT The HMON library is built to support Advanced Expanded Mode 6 only. The Library is also built with the number of parameter registers set to 3 (Default = ...

Page 14

MON ODE IZE HMON is built along with the debug code. Certain elements of the HMON code must remain at a fixed location in memory. The following table details the HMON components and their size and ...

Page 15

M M EMORY AP H'00000000 Vectors H'00001000 FDTInit H'0000111D H'00002000 CUser_Vectors H'00002003 H'00005000 PHMON CHMON H'00007423 H'0000F600 FDTUserModeMicr oKernel H'0000FDF9 H'0003FFFF H'00400000 External SRAM H'0043FFFF H'00FFDC00 On-Chip RAM H'00FFE600 BHMON H'00FFE80E H'00FFEA00 Stack H'00FFEBFF H'00FFFE40 Internal I/O REGISTERS H'00FFFF07 ...

Page 16

AUD ATE ETTING HMON has initially set to connect at 115200 Baud. Should the user wish to change this, the value for the BRR in HMONserialconfiguser.c will need to be changed and the project re-built. Please ...