AD8331-EVAL Analog Devices Inc, AD8331-EVAL Datasheet
AD8331-EVAL
Specifications of AD8331-EVAL
Related parts for AD8331-EVAL
AD8331-EVAL Summary of contents
Page 1
... ADC. An external resistor adjusts the clamping level. The operating temperature range is −40°C to +85°C. The AD8331 is available in a 20-lead QSOP package, the AD8332 is available in 28-lead TSSOP and 32-lead LFCSP packages, and the AD8334 is available in a 64-lead LFCSP package. ...
Page 2
... Measurement Setup.................................................................... 48 Board Layout ............................................................................... 48 Evaluation Board Schematics ................................................... 49 AD8334 Evaluation Board PCB Layers ................................... 51 Outline Dimensions ....................................................................... 53 Ordering Guide .......................................................................... 55 Deleted AD8331 Bill of Materials Section and Table 11; Renumbered Sequentially ............................................................. 43 Changes to Figure 104 ................................................................... 43 Changes to Figure 106 ................................................................... 45 Changes to Figure 107 ................................................................... 46 Changes to Figure 113 ................................................................... 47 Changes to Figure 114 and Board Layout Section ..................... 48 Deleted AD8332 Bill of Materials Section and Table 13 ...
Page 3
... Changes to Figure 83 ...................................................................... 31 Changes to Figure 88 ...................................................................... 32 Switched Figure 89 and Figure 90 ................................................. 33 Changes to Figure 89 ...................................................................... 33 Changes to Ultrasound TGC Application Section...................... 34 Incorporated AD8331-EVAL Data Sheet, Rev. A ....................... 39 Changes to User-Supplied Optional Components Section and Measurement Setup Section ................................................... 39 Changes to Figure 95 ...................................................................... 39 Changes to Figure 97 ...................................................................... 41 Added Figure 98 .............................................................................. 42 Incorporated AD8332-EVALZ Data Sheet, Rev ...
Page 4
... Large Signal Bandwidth AD8331 AD8332, AD8334 Slew Rate AD8331 AD8332, AD8334 Input Voltage Noise Noise Figure Active Termination Match Unterminated Output-Referred Noise AD8331 AD8332, AD8334 Output Impedance, Postamplifier = 50 Ω 280 Ω pF MHz Test Conditions/Comments Single-ended input to differential output Input to output (single-ended) ...
Page 5
... V < V < 0.95 V GAIN 0.10 V < V < 0.95 V GAIN LO gain HI gain 48 dB gain change to 90% full scale Current limited to ± 2 2.0 V p-p OUT Rev Page AD8331/AD8332/AD8334 1 Min Typ Max Unit V ± 1.125 V CM 4.5 V p-p −50 ±5 +50 mV −125 −25 ...
Page 6
... AD8334 Power Dissipation per Channel AD8331 AD8332, AD8334 Power-Down Current AD8331 AD8332 AD8334 LNA Current AD8331 (ENBL) AD8332, AD8334 (ENBL) VGA Current AD8331 (ENBV) AD8332, AD8334 (ENBV) PSRR 1 All dBm values are referred to 50 Ω. 2 The absolute gain refers to the theoretical gain expression in Equation 1. ...
Page 7
... Exposure to absolute V + 200 mV S maximum rating conditions for extended periods may affect V + 200 mV S device reliability. 2.5 V ESD CAUTION 0.96 W 1.97 W 0.78 W 0.91 W −40°C to +85°C −65°C to +150°C 300°C 68°C/W 33°C/W 83°C/W 24.2°C/W Rev Page AD8331/AD8332/AD8334 ...
Page 8
... AD8331/AD8332/AD8334 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS Table 3. 20-Lead QSOP Pin Function Description (AD8331) Pin No. Mnemonic 1 LMD 2 INH 3 VPSL 4 LON 5 LOP 6 COML 7 VIP 8 VIN 9 MODE 10 GAIN 11 VCM 12 RCLMP 13 HILO 14 VPOS 15 VOH 16 VOL 17 COMM 18 ENBV 19 ENBL 20 COMM LMD COMM 1 20 PIN 1 ENBL INH ...
Page 9
... VIN1 VCM1 HILO ENB VOH1 VOL1 VPSV Table 5. 32-Lead LFCSP Pin Function Description (AD8332) Pin No. Mnemonic Rev Page AD8331/AD8332/AD8334 LON1 1 24 PIN 1 INDICATOR VPS1 2 23 INH1 3 22 LMD1 AD8332 4 21 TOP VIEW LMD2 5 20 (Not to Scale) INH2 6 19 VPS2 7 18 LON2 ...
Page 10
... AD8331/AD8332/AD8334 Table 6. 64-Lead LFCSP Pin Function Description (AD8334) Pin No. Mnemonic 1 INH2 2 LMD2 LON2 5 LOP2 6 VIP2 7 VIN2 8 VPS2 9 VPS3 10 VIN3 11 VIP3 12 LOP3 13 LON3 LMD3 16 INH3 17 COM3 18 COM4 19 INH4 20 LMD4 LON4 23 LOP4 24 VIP4 25 VIN4 26 VPS4 INH2 1 PIN 1 INDICATOR LMD2 LON2 4 LOP2 5 VIP2 6 VIN2 ...
Page 11
... CH1 LNA Feedback Output (for Not Connected LNA Midsupply Pin; Connect a Capacitor for Midsupply HF Bypass. CH1 LNA Input. CH1 LNA Ground. CH2 LNA Ground. The exposed paddle must be soldered to the PCB ground to ensure proper heat dissipation, noise, and mechanical strength benefits. Rev Page AD8331/AD8332/AD8334 ...
Page 12
... AD8331/AD8332/AD8334 TYPICAL PERFORMANCE CHARACTERISTICS T = 25° 500 Ω −4 +43.5 dB gain (HILO = LO), and differential output voltage, unless otherwise specified HILO = HILO = LO 0 ASCENDING GAIN MODE DESCENDING GAIN MODE (WHERE AVAILABLE) –10 0 0.2 0.4 0.6 V (V) GAIN Figure 7. Gain vs. V and MODE (MODE Available on RU Package) GAIN 2 ...
Page 13
... GAIN 50Ω 500Ω 1kΩ S 100M 500M Figure 17. Group Delay vs. Frequency for Two Values of AC Coupling 100M 500M Figure 18. Representative Differential Output Offset Voltage vs Ω S Rev Page AD8331/AD8332/AD8334 p-p OUT – 1.0V GAIN AD8332 V = 0.7V –40 GAIN AD8334 V = 0.4V GAIN –60 – ...
Page 14
... AD8331/AD8332/AD8334 35 SAMPLE SIZE = 100 0.2V < V < 0.7V GAIN 49.6 49.7 49.8 49.9 50.0 50.1 GAIN SCALING FACTOR Figure 19. Gain Scaling Factor Histogram 100 SINGLE ENDED, PIN VOH OR PIN VOL ∞ 0.1 100k 1M FREQUENCY (Hz) Figure 20. Output Impedance vs. Frequency 10k 1k 100 R = ∞ 0pF R = 549Ω ...
Page 15
... Figure 28. Short-Circuit, Input-Referred Noise vs. Temperature GAIN 5MHz 0.1 100M 1 7 INCLUDES NOISE OF VGA SIMULATED RESULTS 0 0.8 1.0 50 Figure 30. Noise Figure vs. R GAIN Rev Page AD8331/AD8332/AD8334 ∞ 1V 10MHz GAIN –30 – TEMPERATURE (°C) ∞ GAIN R THERMAL NOISE S ALONE 10 100 SOURCE RESISTANCE (Ω ...
Page 16
... AD8331/AD8332/AD8334 35 PREAMP LIMITED HILO = LO 50Ω IN ∞ HILO = LO HILO = HI 50Ω IN ∞ HILO = HI 0.1 0.2 0.3 0.4 0.5 0.6 V (V) GAIN Figure 31. Noise Figure vs 10MHz 50Ω GAIN (dB) Figure 32. Noise Figure vs. Gain 30dB V = 1Vp-p OUT –10 –20 –30 –40 –50 –60 –70 – ...
Page 17
... Figure 41. Output Third-Order Intercept (IP3) vs. V 2mV 100 50mV 0.8 0.9 1.0 Figure 42. Small Signal Pulse Response dB, Top: Input, Bottom: Output Voltage, HILO = Rev Page AD8331/AD8332/AD8334 p-p COMPOSITE ( + ) OUT 1 2 HILO = LO HILO = HI 10M FREQUENCY (Hz) Figure 40. IMD3 vs. Frequency 1MHz HILO = LO 10MHz HILO = LO ...
Page 18
... AD8331/AD8332/AD8334 20mV 100 500mV Figure 43. Large Signal Pulse Response dB, HILO = HI or LO, Top: Input, Bottom: Output Voltage 30dB 1 INPUT 0 –1 INPUT IS NOT TO SCALE –2 –50 –40 –30 –20 – TIME (ns) Figure 44. Large Signal Pulse Response for Various Capacitive Loads pF, 10 pF 500mV 200mV Figure 45 ...
Page 19
... Figure 52. Enable Response, Large Signal, Top Bottom 150 mV p-p ENB OUT INH 0 VPS1, V GAIN VPSV 0.5V GAIN VPS1, V GAIN 100k 1M 10M FREQUENCY (Hz) Figure 53. PSRR vs. Frequency (No Bypass Capacitor 0.5V GAIN AD8334 AD8332 AD8331 –40 – TEMPERATURE (°C) Figure 54. Quiescent Supply Current vs. Temperature = 0. 100M 80 100 ...
Page 20
... AD8331/AD8332/AD8334 TEST CIRCUITS MEASUREMENT CONSIDERATIONS Figure 55 through Figure 68 show typical measurement configurations and proper interface values for measurements with 50 Ω conditions. Short-circuit input noise measurements are made as shown in Figure 62. The input-referred noise level is determined by Figure 56. Test Circuit—Frequency Response for Various Matched Source Impedances Figure 57. Test Circuit— ...
Page 21
... Figure 60. Test Circuit—Frequency Response for Unterminated LNA, Single-Ended 18nF 270Ω FB* 120nH 0.1µF INH DUT 22pF 0.1µF LMD *FERRITE BEAD Figure 61. Test Circuit—Short-Circuit, Input-Referred Noise Rev Page AD8331/AD8332/AD8334 50Ω IN 0.1µF OR 0.1µF 1µF 237Ω 28Ω VGA 1:1 237Ω LMD 0.1µF 0.1µ ...
Page 22
... AD8331/AD8332/AD8334 49.9Ω 50Ω –6dB LPF 50Ω SIGNAL GENERATOR –6dB LPF 50Ω SIGNAL GENERATOR –6dB +22dB 50Ω –6dB +22dB 50Ω SIGNAL GENERATORS A GAIN 0.1µF FERRITE BEAD 0.1µF 120nH INH DUT 22pF 1Ω 0.1µF 0.1µF SIGNAL GENERATOR LMD ...
Page 23
... FB* 0.1µF 120nH INH DUT 22pF 50Ω LMD RF 0.1µF SIGNAL 0.1µF GENERATOR *FERRITE BEAD Figure 68. Test Circuit—PSRR vs. Frequency Rev Page AD8331/AD8332/AD8334 OSCILLOSCOPE 50Ω IN 28Ω 1:1 28Ω OSCILLOSCOPE CH1 CH2 DIFF PROBE 9.5dB 50Ω PULSE GENERATOR NETWORK ANALYZER 50Ω ...
Page 24
... MID – + ATTENUATOR INH LNA –48dB – + LMD VCM VGA BIAS AND BIAS INTERPOLATOR AD8331 ENBL ENBV Figure 69. AD8331 Functional Block Diagram LON1 LOP1 VIP1 VIN1 +19dB – ATTENUATOR INH1 LNA 1 –48dB + LMD1 VGA BIAS AND LNA V MID INTERPOLATOR LMD2 + ATTENUATOR ...
Page 25
... Low HD2 is particularly important in second harmonic ultrasound imaging applications. Differential signaling enables smaller swings at each output, further reducing third-order distortion. Rev Page AD8331/AD8332/AD8334 AD8331/AD8332/AD8334 (can be the same value as LMD ) is connected from the LMD INH C R ...
Page 26
... AD8331/AD8332/AD8334 Active Impedance Matching The LNA supports active impedance matching through an external shunt feedback resistor from Pin LON to Pin INH. The input resistance given in Equation 5, where A is the single- IN ended gain of 4.5, and 6 kΩ is the unterminated input impedance. × kΩ ...
Page 27
... The inverse gain mode is selected by setting the MODE pin to HI gain mode. Gain control response time is less than 750 ns to settle within 10% of the final value for a change from minimum to maximum gain. Rev Page AD8331/AD8332/AD8334 , with an input range GAIN beyond the control range saturate GAIN < ...
Page 28
... AD8331/AD8332/AD8334 VGA Noise In a typical application, a VGA compresses a wide dynamic range input signal to within the input span of an ADC. While the input-referred noise of the LNA limits the minimum resolvable input signal, the output-referred noise, which depends primarily on the VGA, limits the maximum instantaneous dynamic range that can be processed at any one particular gain control voltage ...
Page 29
... For additional information, see the Applications Information section. The accuracy of the clamping levels is approximately ± mode. Figure 80 illustrates the output characteristics for a few values CLMP AD8331/AD8332/AD8334 5.0 4.5 ∞ CLMP 4.0 8.8kΩ ...
Page 30
... AD8331/AD8332/AD8334 APPLICATIONS INFORMATION LNA—EXTERNAL COMPONENTS The LMD pin (connected to the bias circuitry) must be bypassed to ground and signal sourced to the INH pin, which is capacitively coupled using 2 0.1 μF capacitors (see Figure 81). The unterminated input impedance of the LNA is 6 kΩ. The user can synthesize any LNA input resistance between 50 Ω and 6 kΩ ...
Page 31
... Figure 81. In Figure 81, the resistor value is 84.5 Ω. For example, all the evaluation boards for this series incorporate 100 Ω in parallel with a 120 nH bead. Lower value resistors are permissible for applications with nearby loads or Rev Page AD8331/AD8332/AD8334 HILO = LO HILO = HI 2.5 3.0 3 ...
Page 32
... AD8331/AD8332/AD8334 with gains less than 40 dB. The exact values of these components can be selected empirically. An antialiasing noise filter is typically used with an ADC. Filter requirements are application dependent. When the ADC resides on a separate board, the majority of filter components should be placed nearby to suppress noise picked up between boards and to mitigate charge kickback from the ADC inputs ...
Page 33
... Rev Page AD8331/AD8332/AD8334 ADG736 1.13kΩ SELECT R IZ 280Ω 18nF 5Ω 200Ω INH LNA LMD 50Ω 0.1µF AD8332 Figure 89. Accommodating Multiple Sources AD8331 as an example COMM LMD AD8331 INH ENBL + VPSL ENBV + LON COMM LOP VOL VOUT 6 15 ...
Page 34
... AD8331/AD8332/AD8334 ULTRASOUND TGC APPLICATION The AD8332 ideally meets the requirements of medical and industrial ultrasound applications. The TGC amplifier is a key subsystem in such applications because it provides the means for echo location of reflected ultrasound energy. Figure 91 through Figure 93 are schematics of a dual, fully differential system using the AD8332 and the high speed ADC with conversion speeds as high as 65 MSPS ...
Page 35
... L11 VOL2 VOL1 120nH L10 COMM VPSV 120nH FB R26 100Ω +5VGA C45 C85 0.1µF 1nF AD8332 Rev Page AD8331/AD8332/AD8334 TP6 L13 C60 120nH FB 0.1µ C79 IN1 22pF CFB1 18nF RFB1 274Ω C42 C59 0.1µF 0.1µF ...
Page 36
... AD8331/AD8332/AD8334 VR1 ADP3339AKC-3.3 L5 C44 120nH FB 1µF +5V + C31 0.1µ OUT GND L4 120nH FB C30 OUT 0.1µF TAB L3 120nH FB C29 0.1µF L2 120nH FB C1 0.1µF +3.3VCLK R18 S2 C63 499Ω EXT CLOCK 0.1µF R16 5kΩ R17 R19 49.9Ω ...
Page 37
... C8 C10 C76 0.1µF 0.1µF 10µF 6. +3.3VDVDD + + C27 C7 C9 10µF 0.1µF 0.1µF 6. C75 10µF 0.1µF 0.1µF 0.1µF 6. AD8332 and AD9238 Rev Page AD8331/AD8332/AD8334 R40 22Ω × × 4 RP2 × × SAM080UPM ...
Page 38
... AD8331/AD8332/AD8334 COM3 COM4 INH4 LMD4 NC LON4 LOP4 VIP4 VIN4 VPS4 GAIN34 CLMP34 HILO VCM4 VCM3 NC 03199-094 Figure 94. Compact Signal Path and Board Layout for the Rev Page COM2 COM1 INH1 LMD1 NC LON1 LOP1 VIP1 VIN1 VPS1 GAIN12 CLMP12 EN12 EN34 VCM1 ...
Page 39
... The components shown in black are for typical operation, and the components shown in gray are installed at the user’s discretion. As shipped, the LNA input impedance of the AD8331-EVALZ is configured for 50 Ω to accommodate most signal generators and network analyzers. Input impedances kΩ are realized by changing the values of RFB and CSH ...
Page 40
... AD8331/AD8332/AD8334 AD8331 EVALUATION BOARD SCHEMATICS GND1 GND2 GND +5V C INH L1 0.1µF LNA2 120nH FB PROBE 3 D1 INPUT CLAMP BAT64-04 120nH FB DIODES +5V LON R4 R8 LOP GN_SLOPE COMPONENTS IN GRAY ARE OPTIONAL AND USER SUPPLIED LMD2 COMM 10µF CLMD 10V 0.1µF 2 INH ENB ...
Page 41
... ANALYZER DP8200 PRECISION VOLTAGE REFERENCE (FOR VGAIN) Figure 97 1103 TEKPROBE POWER SUPPLY +5V GND DIFFERENTIAL PROBE TO VO PINS INSERT JUMPERS W5 AND W6 TO USE OUTPUT TRANSFORMER AND VOH SMA AD8331 Typical Board Test Connections Rev Page AD8331/AD8332/AD8334 E3631A POWER SUPPLY ...
Page 42
... AD8331/AD8332/AD8334 AD8331 EVALUATION BOARD PCB LAYERS Figure 98. AD8331-EVALZ Assembly Figure 99. Primary Side Copper Figure 100. Secondary Side Copper Figure 101. Internal Layer Ground Figure 102. Power Plane Figure 103. Top Silkscreen Rev Page ...
Page 43
... RFBx and CSHx. For reference, Table 11 lists the common input impedance values and corresponding adjustments. The board is designed for 0603 size, surface-mount components. AD8331/AD8332/AD8334 Table 11. LNA External Component Values for Common Source Impedances R (Ω) RFB1, RFB2 (Ω ...
Page 44
... AD8331/AD8332/AD8334 EVALUATION BOARD SCHEMATICS +5V GND GND1 GND2 + C25 10µ 0.1µF LNA2 120nH FB CAL2 L8 120nH FB +5V 0.1µF +5VLNA S6 LON2 C9 R10 R12 LOP2 0.1µF TP3 CLAMP RCLMP C11 T2 R13 0.1µF W12 1:1 237Ω VOH2 W6 VO2 R14 W13 237Ω ...
Page 45
... VGAIN SUPPLY Figure 106. NETWORK ANALYZER AD8332 Typical Board Test Connections Rev Page AD8331/AD8332/AD8334 1103 TEKPROBE POWER SUPPLY DIFFERENTIAL PROBE ...
Page 46
... AD8331/AD8332/AD8334 AD8332 EVALUATION BOARD PCB LAYERS Figure 107. AD8332-EVALZ Assembly Figure 108. Primary Side Copper Figure 109. Secondary Side Copper Figure 110. Ground Plane Figure 111. Power Plane Figure 112. Component Side Silkscreen Rev Page ...
Page 47
... The board is shipped assembled and tested, and users need only connect the signal and VGAIN sources and a single 5 V power supply. Figure 113 is a photograph of the board. The AD8334-EVALZ is lead free and RoHS compliant. Figure 113. AD8334-EVALZ Top View Rev Page AD8331/AD8332/AD8334 ...
Page 48
... AD8331/AD8332/AD8334 CONFIGURING THE INPUT IMPEDANCE The board is built and tested using the components shown in black in Figure 115. Provisions are made for optional components (shown in gray) that can be installed at user discretion. As shipped, the input impedances of the low noise amplifiers (LNAs) are configured for 50 Ω to match the output impedances of most signal generators and network analyzers. Input impedances kΩ ...
Page 49
... C32 I N4 0.1 µF L4 ICR4 120 R22 R23 120 +5V 1 LO4 3 CR4 Figure 115. AD8334-EVALZ Schematic Rev Page AD8331/AD8332/AD8334 +5V +5V R49 120 nH 4.02kΩ RX1 100Ω EN34 E E 100Ω C57 D D 0.1 µF C59 120 nH 0.1 µ ...
Page 50
... AD8331/AD8332/AD8334 PRECISION VOLTAGE REFERENCE (FOR VGAIN) NETWORK ANALYZER SIGNAL INPUT Figure 116. GAIN CONTROL VOLTAGE GND AD8334 Typical Board Test Connections (One Channel Shown) Rev Page PROBE POWER SUPPLY +5V DIFFERENTIAL PROBE POWER SUPPLY GND ...
Page 51
... AD8334 EVALUATION BOARD PCB LAYERS Figure 117. AD8334-EVALZ Primary Side Copper Figure 118. AD8334-EVALZ Secondary Side Copper AD8331/AD8332/AD8334 Figure 119. AD8334-EVALZ Inner Layer 1Copper Figure 120. AD8334-EVALZ Inner Layer 2 Copper Rev Page ...
Page 52
... AD8331/AD8332/AD8334 Figure 121. AD8334-EVALZ Component Side Silkscreen Rev Page ...
Page 53
... SEATING PLANE 0.012 (0.30) BSC 0.008 (0.20) COMPLIANT TO JEDEC STANDARDS MO-137-AD Figure 123. 20-Lead Shrink Small Outline Package (QSOP) (RQ-20) Dimensions shown in Inches and (millimeters Rev Page AD8331/AD8332/AD8334 6.40 BSC 8 ° 0.75 0 ° 0.60 0.45 0.010 (0.25) 0.020 (0.51) 0.006 (0.15) ...
Page 54
... AD8331/AD8332/AD8334 PIN 1 INDICATOR 12° MAX 1.00 0.85 0.80 SEATING PLANE BSC SQ PIN 1 INDICATOR 1.00 12° MAX 0.85 0.80 SEATING PLANE 5.00 BSC SQ 0.60 MAX 24 0.50 BSC TOP 4.75 VIEW BSC SQ 0.50 0.40 17 0.30 0.80 MAX 0.65 TYP 0.05 MAX 0.02 NOM ...
Page 55
... AD8331ARQ-REEL7 –40°C to +85°C AD8331ARQZ –40°C to +85°C AD8331ARQZ-RL –40°C to +85°C AD8331ARQZ-R7 –40°C to +85°C AD8331-EVALZ AD8332ACP-R2 –40°C to +85°C AD8332ACP-REEL –40°C to +85°C AD8332ACP-REEL7 –40°C to +85°C AD8332ACPZ-R2 –40°C to +85°C AD8332ACPZ-R7 – ...
Page 56
... AD8331/AD8332/AD8334 NOTES ©2003–2010 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D03199-0-10/10(G) Rev Page ...