PIC16F1938-I/ML Microchip Technology, PIC16F1938-I/ML Datasheet - Page 285

• Manufacturer Part Number: PIC16F1938-I/ML
• Description: IC MCU 8BIT FLASH 28QFN
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 16Fr

Specifications of PIC16F1938-I/ML

• Core Size: 8-Bit
• Program Memory Size: 28KB (16K x 14)
• Oscillator Type: Internal
• Core Processor: PIC
• Speed: 32MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Controller Family/series: PIC16F
• No. Of I/o's: 25
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 1024Byte
• Cpu Speed: 32MHz
• Package: 28QFN EP
• Device Core: PIC
• Family Name: PIC16
• Maximum Speed: 32 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 25
• Interface Type: I2C/SPI/USART
• On-chip Adc: 11-chx10-bit
• Number Of Timers: 5
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

22.3.5
The master can initiate the data transfer at any time
because it controls the SCK. The master determines
when the slave (Processor 2, Figure 22-4) is to
broadcast data by the software protocol.
In Master mode, the data is transmitted/received as
soon as the SSPBUF register is written to. If the SPI is
only going to receive, the SDO output could be dis-
abled (programmed as an input). The SSPSR register
will continue to shift in the signal present on the SDI pin
at the programmed clock rate. As each byte is
received, it will be loaded into the SSPBUF register as
if a normal received byte (interrupts and Status bits
appropriately set).
FIGURE 22-5:
© 2009 Microchip Technology Inc.
Write to
SSPBUF
SCK
(CKP = 0
CKE = 0)
SCK
(CKP = 1
CKE = 0)
SCK
(CKP = 0
CKE = 1)
SCK
(CKP = 1
CKE = 1)
SDO
(CKE = 0)
SDO
(CKE = 1)
SDI
(SMP = 0)
Input
Sample
(SMP = 0)
SDI
(SMP = 1)
Input
Sample
(SMP = 1)
SSPIF
SSPSR to
SSPBUF
MASTER MODE
SPI MODE WAVEFORM (MASTER MODE)
bit 7
bit 7
bit 7
bit 7
bit 6
bit 6
bit 5
bit 5
Preliminary
bit 4
bit 4
bit 3
bit 3
The clock polarity is selected by appropriately
programming the CKP bit of the SSPCON1 register
and the CKE bit of the SSPSTAT register. This then,
would give waveforms for SPI communication as
shown in Figure 22-5, Figure 22-6 and Figure 22-7,
where the MSB is transmitted first. In Master mode, the
SPI clock rate (bit rate) is user programmable to be one
of the following:
• F
• F
• F
• Timer2 output/2
• Fosc/(4 * (SSPADD + 1))
Figure 22-5 shows the waveforms for Master mode.
When the CKE bit is set, the SDO data is valid before
there is a clock edge on SCK. The change of the input
sample is shown based on the state of the SMP bit. The
time when the SSPBUF is loaded with the received
data is shown.
PIC16F193X/LF193X
OSC
OSC
OSC
/4 (or T
/16 (or 4 * T
/64 (or 16 * T
bit 2
bit 2
CY
)
bit 1
bit 1
CY
CY
)
)
bit 0
bit 0
bit 0
bit 0
DS41364C-page 285
4 Clock
Modes