DSPIC30F3011-20I/ML Microchip Technology, DSPIC30F3011-20I/ML Datasheet - Page 93
![IC DSPIC MCU/DSP 24K 44QFN](/photos/6/81/68122/150-44-qfn_sml.jpg)
DSPIC30F3011-20I/ML
Manufacturer Part Number
DSPIC30F3011-20I/ML
Description
IC DSPIC MCU/DSP 24K 44QFN
Manufacturer
Microchip Technology
Series
dsPIC™ 30Fr
Datasheets
1.DSPIC30F3010-30ISO.pdf
(228 pages)
2.DSPIC30F3010-30ISO.pdf
(18 pages)
3.DSPIC30F3010-30ISO.pdf
(6 pages)
4.DSPIC30F3010-30ISO.pdf
(16 pages)
5.DSPIC30F3010-30ISO.pdf
(22 pages)
6.DSPIC30F3010-20ISP.pdf
(226 pages)
Specifications of DSPIC30F3011-20I/ML
Core Processor
dsPIC
Core Size
16-Bit
Speed
20 MIPS
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
Number Of I /o
30
Program Memory Size
24KB (8K x 24)
Program Memory Type
FLASH
Eeprom Size
1K x 8
Ram Size
1K x 8
Voltage - Supply (vcc/vdd)
2.5 V ~ 5.5 V
Data Converters
A/D 9x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
44-QFN
Core Frequency
40MHz
Core Supply Voltage
5.5V
Embedded Interface Type
I2C, SPI, UART
No. Of I/o's
30
Flash Memory Size
24KB
Supply Voltage Range
2.5V To 5.5V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
XLT44QFN2 - SOCKET TRAN ICE 44QFN/40DIPAC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
DSPIC30F301120IML
14.3
There are two measurement modes which are sup-
ported and are termed x2 and x4. These modes are
selected by the QEIM<2:0> mode select bits located in
SFR, QEICON<10:8>.
When control bits, QEIM<2:0> = 100 or 101, the x2
Measurement mode is selected and the QEI logic only
looks at the Phase A input for the position counter
increment rate. Every rising and falling edge of the
Phase A signal causes the position counter to be
incremented or decremented. The Phase B signal is
still utilized for the determination of the counter
direction, just as in the x4 Measurement mode.
Within the x2 Measurement mode, there are two
variations of how the position counter is reset:
1.
2.
When control bits, QEIM<2:0> = 110 or 111, the x4
Measurement mode is selected and the QEI logic looks
at both edges of the Phase A and Phase B input
signals. Every edge of both signals causes the position
counter to increment or decrement.
Within the x4 Measurement mode, there are two
variations of how the position counter is reset:
1.
2.
The x4 Measurement mode provides for finer
resolution data (more position counts) for determining
motor position.
14.4
The digital noise filter section is responsible for
rejecting noise on the incoming quadrature signals.
Schmitt Trigger inputs and a three-clock cycle delay
filter combine to reject low level noise and large, short
duration noise spikes that typically occur in noise prone
applications, such as a motor system.
The filter ensures that the filtered output signal is not
permitted to change until a stable value has been
registered for three consecutive clock cycles.
For the QEA, QEB and INDX pins, the clock divide
frequency for the digital filter is programmed by bits,
QECK<2:0> (DFLTCON<6:4>), and are derived from
the base instruction cycle, T
To enable the filter output for channels, QEA, QEB and
INDX, the QEOUT bit must be ‘1’. The filter network for
all channels is disabled on POR and BOR.
© 2010 Microchip Technology Inc.
Position counter reset by detection of index
pulse, QEIM<2:0> = 100.
Position counter reset by match with MAXCNT,
QEIM<2:0> = 101.
Position counter reset by detection of index
pulse, QEIM<2:0> = 110.
Position counter reset by match with MAXCNT,
QEIM<2:0> = 111.
Position Measurement Mode
Programmable Digital Noise
Filters
CY
.
14.5
When the QEI module is not configured for the QEI
mode, QEIM<2:0> = 001, the module can be
configured as a simple 16-bit timer/counter. The setup
and control of the auxiliary timer is accomplished
through the QEICON SFR register. This timer functions
identically to Timer1. The QEA pin is used as the timer
clock input.
When configured as a timer, the POSCNT register
serves as the Timer Count register and the MAXCNT
register serves as the Period register. When a Timer/
Period register match occurs, the QEI interrupt flag will
be asserted.
The only exception between the general purpose
timers and this timer is the added feature of external
up/down input select. When the UPDN pin is asserted
high, the timer will increment up. When the UPDN pin
is asserted low, the timer will be decremented.
The UPDN control/status bit (QEICON<11>) can be
used to select the count direction state of the Timer
register. When UPDN = 1, the timer will count up. When
UPDN = 0, the timer will count down.
In addition, control bit, UPDN_SRC (QEICON<0>),
determines whether the timer count direction state is
based on the logic state written into the UPDN control/
status bit (QEICON<11>), or the QEB pin state. When
UPDN_SRC = 1, the timer count direction is controlled
from the QEB pin. Likewise, when UPDN_SRC = 0, the
timer count direction is controlled by the UPDN bit.
14.6
14.6.1
The QEI module will be halted during the CPU Sleep
mode.
14.6.2
During CPU Sleep mode, the timer will not operate,
because the internal clocks are disabled.
Note:
Note:
dsPIC30F3010/3011
Alternate 16-Bit Timer/Counter
QEI Module Operation During CPU
Sleep Mode
Changing the operational mode (i.e., from
QEI to timer or vice versa), will not affect
the Timer/Position Count register contents.
This timer does not support the External
Asynchronous Counter mode of operation.
If using an external clock source, the clock
will automatically be synchronized to the
internal instruction cycle.
QEI OPERATION DURING CPU
SLEEP MODE
TIMER OPERATION DURING CPU
SLEEP MODE
DS70141F-page 93