PIC24HJ64GP506A-I/PT Microchip Technology, PIC24HJ64GP506A-I/PT Datasheet - Page 163

• Manufacturer Part Number: PIC24HJ64GP506A-I/PT
• Description: IC PIC MCU FLASH 64KB 64-TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 24Hr

Specifications of PIC24HJ64GP506A-I/PT

• Core Size: 16-Bit
• Program Memory Size: 64KB (22K x 24)
• Core Processor: PIC
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 18x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Controller Family/series: PIC24
• No. Of I/o's: 53
• Ram Memory Size: 8KB
• Cpu Speed: 40MHz
• No. Of Timers: 9
• Interface: CAN, I2C, SPI, UART
• Embedded Interface Type: CAN, I2C, SPI, UART
• Rohs Compliant: Yes
• Processor Series: PIC24HJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 8192 B
• Interface Type: SPI, I2C, UART
• Maximum Clock Frequency: 7.37 MHz
• Number Of Timers: 13
• Operating Supply Voltage: 3 V to 3.6 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1004 - PIC24 BREAKOUT BOARD
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

REGISTER 16-2:
 2009 Microchip Technology Inc.
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15-13
bit 12
bit 11
bit 10
bit 9
bit 8
bit 7
bit 6
bit 5
Note 1: The CKE bit is not used in the Framed SPI modes. The user should program this bit to ‘0’ for the Framed
SSEN
R/W-0
U-0
—
2: Do not set both Primary and Secondary prescalers to a value of 1:1.
3: This bit must be cleared when FRMEN = 1.
(3)
SPI modes (FRMEN = 1).
Unimplemented: Read as ‘0’
DISSCK: Disable SCKx pin bit (SPI Master modes only)
1 = Internal SPI clock is disabled, pin functions as I/O
0 = Internal SPI clock is enabled
DISSDO: Disable SDOx pin bit
1 = SDOx pin is not used by module; pin functions as I/O
0 = SDOx pin is controlled by the module
MODE16: Word/Byte Communication Select bit
1 = Communication is word-wide (16 bits)
0 = Communication is byte-wide (8 bits)
SMP: SPIx Data Input Sample Phase bit
Master mode:
1 = Input data sampled at end of data output time
0 = Input data sampled at middle of data output time
Slave mode:
SMP must be cleared when SPIx is used in Slave mode.
CKE: SPIx Clock Edge Select bit
1 = Serial output data changes on transition from active clock state to Idle clock state (see bit 6)
0 = Serial output data changes on transition from Idle clock state to active clock state (see bit 6)
SSEN: Slave Select Enable bit (Slave mode)
1 = SSx pin used for Slave mode
0 = SSx pin not used by module. Pin controlled by port function
CKP: Clock Polarity Select bit
1 = Idle state for clock is a high level; active state is a low level
0 = Idle state for clock is a low level; active state is a high level
MSTEN: Master Mode Enable bit
1 = Master mode
0 = Slave mode
R/W-0
CKP
U-0
—
SPI
X
CON1: SPIx CONTROL REGISTER 1
W = Writable bit
‘1’ = Bit is set
PIC24HJXXXGPX06A/X08A/X10A
MSTEN
R/W-0
U-0
—
DISSCK
R/W-0
R/W-0
(1)
Preliminary
U = Unimplemented bit, read as ‘0’
SPRE<2:0>
‘0’ = Bit is cleared
(3)
DISSDO
R/W-0
R/W-0
(2)
MODE16
R/W-0
R/W-0
x = Bit is unknown
R/W-0
R/W-0
SMP
PPRE<1:0>
DS70592B-page 163
CKE
R/W-0
R/W-0
(2)
(1)
bit 8
bit 0