PIC24HJ64GP506A-I/PT Microchip Technology, PIC24HJ64GP506A-I/PT Datasheet - Page 181

• Manufacturer Part Number: PIC24HJ64GP506A-I/PT
• Description: IC PIC MCU FLASH 64KB 64-TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 24Hr

Specifications of PIC24HJ64GP506A-I/PT

• Core Size: 16-Bit
• Program Memory Size: 64KB (22K x 24)
• Core Processor: PIC
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 18x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Controller Family/series: PIC24
• No. Of I/o's: 53
• Ram Memory Size: 8KB
• Cpu Speed: 40MHz
• No. Of Timers: 9
• Interface: CAN, I2C, SPI, UART
• Embedded Interface Type: CAN, I2C, SPI, UART
• Rohs Compliant: Yes
• Processor Series: PIC24HJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 8192 B
• Interface Type: SPI, I2C, UART
• Maximum Clock Frequency: 7.37 MHz
• Number Of Timers: 13
• Operating Supply Voltage: 3 V to 3.6 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1004 - PIC24 BREAKOUT BOARD
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

19.0
19.1
The Enhanced Controller Area Network (ECAN™)
module is a serial interface, useful for communicating
with other CAN modules or microcontroller devices.
This interface/protocol was designed to allow commu-
nications
PIC24HJXXXGPX06A/X08A/X10A devices contain up
to two ECAN modules.
The CAN module is a communication controller imple-
menting the CAN 2.0 A/B protocol, as defined in the
BOSCH specification. The module will support CAN 1.2,
CAN 2.0A, CAN 2.0B Passive and CAN 2.0B Active
versions of the protocol. The module implementation is
a full CAN system. The CAN specification is not covered
within this data sheet. The reader may refer to the
BOSCH CAN specification for further details.
The module features are as follows:
• Implementation of the CAN protocol, CAN 1.2,
• Standard and extended data frames
• 0-8 bytes data length
• Programmable bit rate up to 1 Mbit/sec
• Automatic response to remote transmission
• Up to 8 transmit buffers with application specified
• Up to 32 receive buffers (each buffer may contain
• Up to 16 full (standard/extended identifier)
• 3 full acceptance filter masks
• DeviceNet™ addressing support
• Programmable wake-up functionality with
• Programmable Loopback mode supports self-test
 2009 Microchip Technology Inc.
CAN 2.0A and CAN 2.0B
requests
prioritization and abort capability (each buffer may
contain up to 8 bytes of data)
up to 8 bytes of data)
acceptance filters
integrated low-pass filter
operation
Note 1: This data sheet summarizes the features
2: Some registers and associated bits
ENHANCED CAN (ECAN™)
MODULE
Overview
of the PIC24HJXXXGPX06A/X08A/X10A
family of devices. However, it is not
intended to be a comprehensive refer-
ence source. To complement the informa-
tion in this data sheet, refer to the
“dsPIC33F/PIC24H Family Reference
Manual”, Section 21. “Enhanced Con-
troller
(DS70226), which is available from the
Microchip website (www.microchip.com).
described in this section may not be avail-
able on all devices. Refer to Section 4.0
“Memory Organization” in this data
sheet for device-specific register and bit
information.
within
Area
noisy
Network
PIC24HJXXXGPX06A/X08A/X10A
environments.
(ECAN™)”
The
Preliminary
• Signaling via interrupt capabilities for all CAN
• Programmable clock source
• Programmable link to input capture module (IC2
• Low-power Sleep and Idle mode
The CAN bus module consists of a protocol engine and
message buffering/control. The CAN protocol engine
handles all functions for receiving and transmitting
messages on the CAN bus. Messages are transmitted
by first loading the appropriate data registers. Status
and errors can be checked by reading the appropriate
registers. Any message detected on the CAN bus is
checked for errors and then matched against filters to
see if it should be received and stored in one of the
receive registers.
19.2
The CAN module transmits various types of frames
which include data messages, remote transmission
requests and as other frames that are automatically
generated for control purposes. The following frame
types are supported:
• Standard Data Frame:
• Extended Data Frame:
• Remote Frame:
• Error Frame:
• Overload Frame:
• Interframe Space:
receiver and transmitter error states
for both CAN1 and CAN2) for time-stamping and
network synchronization
A standard data frame is generated by a node when
the node wishes to transmit data. It includes an 11-bit
standard identifier (SID) but not an 18-bit extended
identifier (EID).
An extended data frame is similar to a standard data
frame but includes an extended identifier as well.
It is possible for a destination node to request the
data from the source. For this purpose, the
destination node sends a remote frame with an iden-
tifier that matches the identifier of the required data
frame. The appropriate data source node will then
send a data frame as a response to this remote
request.
An error frame is generated by any node that detects
a bus error. An error frame consists of two fields: an
error flag field and an error delimiter field.
An overload frame can be generated by a node as a
result of two conditions. First, the node detects a
dominant bit during interframe space which is an ille-
gal condition. Second, due to internal conditions, the
node is not yet able to start reception of the next
message. A node may generate a maximum of 2
sequential overload frames to delay the start of the
next message.
Interframe space separates a proceeding frame (of
whatever type) from a following data or remote
frame.
Frame Types
DS70592B-page 181