PIC18F2220-I/SO Microchip Technology, PIC18F2220-I/SO Datasheet - Page 181

• Manufacturer Part Number: PIC18F2220-I/SO
• Description: IC MCU FLASH 2KX16 A/D 28SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F2220-I/SO

• Core Size: 8-Bit
• Program Memory Size: 4KB (2K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Controller Family/series: PIC18
• No. Of I/o's: 25
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 512Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SPI, I2C, USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 2 x 8 bit
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE4000, ICE2000, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 10 Channel
• Data Rom Size: 256 B
• A/d Bit Size: 10 bit
• A/d Channels Available: 10
• Height: 2.31 mm
• Length: 17.87 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.2 V
• Width: 7.49 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT28SO-1 - SOCKET TRANSITION 28SOIC 300MIL
• Lead Free Status / Rohs Status: Details

17.4.6
Master mode is enabled by setting and clearing the
appropriate SSPM bits in SSPCON1 and by setting the
SSPEN bit. In Master mode, the SCL and SDA lines
are manipulated by the MSSP hardware.
Master mode of operation is supported by interrupt
generation on the detection of the Start and Stop con-
ditions. The Stop (P) and Start (S) bits are cleared from
a Reset or when the MSSP module is disabled. Control
of the I
bus is Idle, with both the S and P bits clear.
In Firmware Controlled Master mode, user code
conducts all I
Stop bit conditions.
Once Master mode is enabled, the user has six
options.
1.
2.
3.
4.
5.
6.
FIGURE 17-16:
© 2007 Microchip Technology Inc.
Assert a Start condition on SDA and SCL.
Assert a Repeated Start condition on SDA and
SCL.
Write
transmission of data/address.
Configure the I
Generate an Acknowledge condition at the end
of a received byte of data.
Generate a Stop condition on SDA and SCL.
2
C bus may be taken when the P bit is set or the
SDA
SCL
MASTER MODE
to
2
C bus operations based on Start and
the
2
C port to receive data.
SSPBUF
MSSP BLOCK DIAGRAM (I
SDA In
register
Bus Collision
SCL In
initiating
PIC18F2220/2320/4220/4320
Read
MSb
Write Collision Detect
end of XMIT/RCV
Start bit, Stop bit,
State Counter for
Clock Arbitration
Start bit Detect
Stop bit Detect
Acknowledge
2
SSPBUF
Generate
SSPSR
C MASTER MODE)
The following events will cause MSSP Interrupt Flag
bit, SSPIF, to be set (MSSP interrupt if enabled):
• Start Condition
• Stop Condition
• Data Transfer Byte Transmitted/Received
• Acknowledge Transmit
• Repeated Start
LSb
Note:
Write
Clock
Data Bus
Shift
Internal
Set/Reset, S, P, WCOL (SSPSTAT);
Set SSPIF, BCLIF;
Reset ACKSTAT, PEN (SSPCON2)
The MSSP module, when configured in
I
of events. For instance, the user is not
allowed to initiate a Start condition and
immediately write the SSPBUF register to
initiate transmission before the Start condi-
tion is complete. In this case, the SSPBUF
will not be written to and the WCOL bit will
be set, indicating that a write to the
SSPBUF did not occur.
2
C Master mode, does not allow queueing
SSPM3:SSPM0
SSPADD<6:0>
Generator
DS39599G-page 179
Baud
Rate