PIC18F2220-I/SO Microchip Technology, PIC18F2220-I/SO Datasheet - Page 211

• Manufacturer Part Number: PIC18F2220-I/SO
• Description: IC MCU FLASH 2KX16 A/D 28SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F2220-I/SO

• Core Size: 8-Bit
• Program Memory Size: 4KB (2K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Controller Family/series: PIC18
• No. Of I/o's: 25
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 512Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SPI, I2C, USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 2 x 8 bit
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE4000, ICE2000, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 10 Channel
• Data Rom Size: 256 B
• A/d Bit Size: 10 bit
• A/d Channels Available: 10
• Height: 2.31 mm
• Length: 17.87 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.2 V
• Width: 7.49 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT28SO-1 - SOCKET TRANSITION 28SOIC 300MIL
• Lead Free Status / Rohs Status: Details

18.5
Synchronous Slave mode differs from the Master mode
in the fact that the shift clock is supplied externally at
the RC6/TX/CK pin (instead of being supplied internally
in Master mode). This allows the device to transfer or
receive data while in any power-managed mode. Slave
mode is entered by clearing bit, CSRC (TXSTA<7>).
18.5.1
The operation of the Synchronous Master and Slave
modes is identical, except in the case of the Sleep
mode.
If two words are written to the TXREG and then the
SLEEP instruction is executed, the following will occur:
a)
b)
c)
d)
e)
TABLE 18-10: REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE TRANSMISSION
© 2007 Microchip Technology Inc.
INTCON
PIR1
PIE1
IPR1
RCSTA
TXREG
TXSTA
SPBRG
Legend: x = unknown, - = unimplemented, read as ‘0’. Shaded cells are not used for synchronous slave transmission.
Note 1:
Name
The first word will immediately transfer to the
TSR register and transmit.
The second word will remain in TXREG register.
Flag bit, TXIF, will not be set.
When the first word has been shifted out of TSR,
the TXREG register will transfer the second
word to the TSR and flag bit, TXIF, will now be
set.
If enable bit, TXIE, is set, the interrupt will wake
the chip from Sleep. If the global interrupt is
enabled, the program will branch to the interrupt
vector.
USART Synchronous Slave Mode
The PSPIF, PSPIE and PSPIP bits are reserved on the PIC18F2X20 devices; always maintain these bits clear.
USART Transmit Register
Baud Rate Generator Register
USART SYNCHRONOUS SLAVE
TRANSMIT
PSPIF
PSPIE
PSPIP
CSRC
SPEN
GIEH
Bit 7
GIE/
(1)
(1)
(1)
PEIE/
ADIE
ADIP
GIEL
ADIF
Bit 6
RX9
TX9
TMR0IE INT0IE
SREN
TXEN
RCIF
RCIE
RCIP
Bit 5
CREN ADDEN
SYNC
TXIF
TXIE
TXIP
Bit 4
PIC18F2220/2320/4220/4320
SSPIE
SSPIP
SSPIF
RBIE
Bit 3
—
TMR0IF
CCP1IE TMR2IE TMR1IE 0000 0000 0000 0000
CCP1IP TMR2IP TMR1IP 1111 1111 1111 1111
CCP1IF TMR2IF TMR1IF 0000 0000 0000 0000
BRGH
FERR
Bit 2
To set up a Synchronous Slave Transmission:
1.
2.
3.
4.
5.
6.
7.
8.
Enable the synchronous slave serial port by
setting bits, SYNC and SPEN, and clearing bit,
CSRC.
Clear bits, CREN and SREN.
If interrupts are desired, set enable bit, TXIE.
If 9-bit transmission is desired, set bit, TX9.
Enable the transmission by setting enable bit,
TXEN.
If 9-bit transmission is selected, the ninth bit
should be loaded in bit TX9D.
Start transmission by loading data to the TXREG
register.
If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
INT0IF
OERR
TRMT
Bit 1
RX9D
TX9D
RBIF
Bit 0
0000 000x 0000 000u
0000 000x 0000 000x
0000 0000 0000 0000
0000 -010 0000 -010
0000 0000 0000 0000
POR, BOR
Value on
DS39599G-page 209
Value on
all other
Resets