ATMEGA1280V-8AU Atmel, ATMEGA1280V-8AU Datasheet - Page 289

• Manufacturer Part Number: ATMEGA1280V-8AU
• Description: IC MCU AVR 128K FLASH 100-TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA1280V-8AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 86
• Program Memory Size: 128KB (64K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• Processor Series: ATMEGA128x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 8 KB
• Interface Type: 2-Wire/SPI/USART
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 86
• Number Of Timers: 6
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16-ch x 10-bit
• Package: 100TQFP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 8 MHz
• Controller Family/series: AVR MEGA
• No. Of I/o's: 86
• Eeprom Memory Size: 4KB
• Ram Memory Size: 8KB
• Cpu Speed: 8MHz
• Rohs Compliant: Yes
• For Use With: ATSTK600-TQFP100 - STK600 SOCKET/ADAPTER 100-TQFP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1005 - ISP 4PORT FOR ATMEL AVR MCU JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK503 - STARTER KIT AVR EXP MODULE 100PATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

25.8
25.8.1
2549M–AVR–09/10
Register Description
ADMUX – ADC Multiplexer Selection Register
Table 25-2.
Example:
ADMUX = 0xFB (ADC3 - ADC2, 10x gain, 2.56V reference, left adjusted result).
Voltage on ADC3 is 300 mV, voltage on ADC2 is 500 mV.
ADCR = 512 × 10 × (300 - 500) / 2560 = -400 = 0x270.
ADCL will thus read 0x00, and ADCH will read 0x9C. Writing zero to ADLAR right adjusts the
result: ADCL = 0x70, ADCH = 0x02.
• Bit 7:6 – REFS1:0: Reference Selection Bits
These bits select the voltage reference for the ADC, as shown in
changed during a conversion, the change will not go in effect until this conversion is complete
(ADIF in ADCSRA is set). The internal voltage reference options may not be used if an external
reference voltage is being applied to the AREF pin.
Table 25-3.
Note:
Bit
(0x7C)
Read/Write
Initial Value
V
V
V
...
V
V
V
...
V
V
V
ADCn
ADCm
ADCm
ADCm
ADCm
ADCm
ADCm
ADCm
REFS1
ADCm
0
0
1
1
+ 0.999 V
+ 0.998 V
+ 0.001 V
- 0.001 V
- 0.999 V
- V
+ V
1. If 10x or 200x gain is selected, only 2.56 V should be used as Internal Voltage Reference. For
REF
REF
differential conversion, only 1.1V cannot be used as internal voltage reference.
/ GAIN
/ GAIN
Correlation Between Input Voltage and Output Codes
Voltage Reference Selections for ADC
REFS0
REFS1
REF
REF
REF
REF
REF
R/W
7
0
0
1
0
1
/ GAIN
/ GAIN
/ GAIN
/ GAIN
/ GAIN
REFS0
R/W
Voltage Reference Selection
AREF, Internal V
AVCC with external capacitor at AREF pin
Internal 1.1V Voltage Reference with external capacitor at AREF pin
Internal 2.56V Voltage Reference with external capacitor at AREF pin
6
0
ATmega640/1280/1281/2560/2561
ADLAR
R/W
Read Code
0x1FF
0x1FF
0x1FE
...
0x001
0x000
0x3FF
...
0x201
0x200
5
0
REF
MUX4
R/W
turned off
4
0
MUX3
R/W
(1)
3
0
MUX2
R/W
Corresponding Decimal Value
2
0
Table
MUX1
R/W
1
0
25-3. If these bits are
-511
-512
511
511
510
...
-1
...
1
0
MUX0
R/W
0
0
ADMUX
289