C8051F040-GQ Silicon Laboratories Inc, C8051F040-GQ Datasheet - Page 232

• Manufacturer Part Number: C8051F040-GQ
• Description: IC 8051 MCU 64K FLASH 100TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F04xr

Specifications of C8051F040-GQ

• Program Memory Type: FLASH
• Program Memory Size: 64KB (64K x 8)
• Package / Case: 100-TQFP, 100-VQFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: CAN, EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 64
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x8b, 13x12b; D/A 2x10b, 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F0x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 4.25 KB
• Interface Type: CAN/SMBus/SPI/UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 64
• Number Of Timers: 5
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F040DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 8-bit or 13-ch x 12-bit
• On-chip Dac: 2-ch x 12-bit
• No. Of I/o's: 64
• Ram Memory Size: 4352Byte
• Cpu Speed: 25MHz
• No. Of Timers: 5
• Rohs Compliant: Yes
• Data Rom Size: 64 KB
• A/d Bit Size: 12 bit
• A/d Channels Available: 13
• Height: 1 mm
• Length: 14 mm
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.7 V
• Width: 14 mm
• Package: 100TQFP
• Device Core: 8051
• Family Name: C8051F04x
• Maximum Speed: 25 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1205 - DEV KIT FOR F040/F041/F042/F043
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1204

Note 1: If Phase_Seg1 + Phase_Seg2 is even, then Phase_Seg2 = Phase_Seg1.
Note 2: Phase_Seg2 should be at least 2 t
C8051F040/1/2/3/4/5/6/7
We will adjust the length of the 4 bit segments so that their sum is as close as possible to the desired bit
time. Since each segment must be an integer multiple of the time quantum (t
time is 22 t
Prop_Seg must be greater than or equal to the propagation delay of 400 ns; we choose 9 t
The remaining time quanta (t
shown in Figure 18.1. We select Phase_Seg1 = 6 t
The Synchronization Jump Width (SJW) timing parameter is defined by Figure 18.2. It is used for determin-
ing the value written to the Bit Timing Register and for determining the required oscillator tolerance. Since
we are using a quartz crystal as the system clock source, an oscillator tolerance calculation is not needed.
The value written to the Bit Timing Register can be calculated using Equation 18.3. The BRP Extension
register is left at its reset value of 0x0000.
232
BRPE = BRP - 1 = BRP Extension Register = 0x0000
SJWp = SJW - 1 = min ( 4, 6 ) – 1 = 3
TSEG1 = (Prop_Seg + Phase_Seg1 - 1) = 9 + 6 - 1 = 14
TSEG2 = (Phase_Seg2 - 1) = 5
Bit Timing Register = (TSEG2 * 0x1000) + (TSEG1 * 0x0100) + (SJWp * 0x0040) + BRPE = 0x5EC0
Otherwise, Phase_Seg2 = Phase_Seg1 + 1.
q
(994.642 ns), yielding a bit rate of 1.00539 Mbit/sec. The Sync_Seg is a constant 1 t
Equation 18.3. Calculating the Bit Timing Register Value
Equation 18.2. Synchronization Jump Width (SJW)
Phase_Seg1
Equation 18.1. Assigning the Phase Segments
q
) in the bit time are divided between Phase_Seg1 and Phase_Seg2 as
+
SJW = min ( 4, Phase_Seg1 )
Phase_Seg2
q
.
=
Rev. 1.4
q
Bit Time
and Phase_Seg2 = 6 t
–
(
Sync_Seg
+
Prop_Seg
q
.
q
), the closest achievable bit
)
q
(406.899 ns).
q
. The