PIC18F1320-I/ML Microchip Technology, PIC18F1320-I/ML Datasheet - Page 14

• Manufacturer Part Number: PIC18F1320-I/ML
• Description: IC MCU FLASH 4KX16 EEPROM 28QFN
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F1320-I/ML

• Core Size: 8-Bit
• Program Memory Size: 8KB (4K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 7x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Controller Family/series: PIC18
• No. Of I/o's: 16
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 256Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Package: 28QFN EP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 16
• Interface Type: USART
• On-chip Adc: 7-chx10-bit
• Number Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT28QFN3 - SOCKET TRAN ICE 18DIP/28QFNAC164322 - MODULE SOCKET MPLAB PM3 28/44QFNAC164033 - ADAPTER 28QFN TO 18DIPDV007003 - PROGRAMMER UNIVERSAL PROMATE II
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC18FX220/X320
FIGURE 3-6:
3.3.1
All of the programming examples, up to this point, have
assumed that the device is blank prior to programming.
In fact, if the device is not blank, the direction has been
to completely erase the device via a Bulk Erase
operation (see Section 3.2 “High-Voltage ICSP Bulk
Erase”).
It may be the case, however, that the user wishes to
modify only a section of an already programmed
device. In such a situation, erasing the entire device is
not a realistic option.
The minimum amount of data that can be written to the
device is 8 bytes. This is accomplished by loading the
8-byte write buffer for the panel and then initiating a
write sequence. In this case, however, it is assumed
that the address space to be written already has data in
it (i.e., it is not blank).
The minimum amount of code memory that may be
erased at a given time is one row of 64 bytes and it is
selected using the TBLPTR registers. The sixth LSb of
the TBLPTR address is ignored. The EECON1 register
must then be used to erase the 64-byte target space
prior to writing the data. This is known as a “Row
Erase”.
DS39592F-page 14
PGC
PGD
1
1
4-Bit Command
MODIFYING CODE MEMORY
2
1
3
1
4
1
TABLE WRITE AND START PROGRAMMING INSTRUCTION TIMING (1111)
P5
1
n
2
n
3
16-Bit Data Payload
n
4
n
5
n
6
n
15 16
PGD = Input
n
n
P5A
When using the EECON1 register to act on code mem-
ory, the EEPGD bit must be set (EECON1<7> = 1) and
the CFGS bit must be cleared (EECON1<6> = 0). The
WREN bit must be set (EECON1<2> = 1) to enable
writes of any sort (e.g., erases), and this must be done
prior to initiating a write sequence. The FREE bit must
be set (EECON1<4> = 1) in order to erase the program
space being pointed to by the Table Pointer. The erase
sequence is initiated by the setting the WR bit
(EECON1<1> = 1). It is strongly recommended that the
WREN bit be set only when absolutely necessary.
To help prevent inadvertent writes when using the
EECON1 register, EECON2 is used to “enable” the WR
bit. This register must be sequentially loaded with 55h,
and then 0AAh, immediately prior to asserting the WR
bit in order for the write to occur.
The erase will begin on the falling edge of the 4th PGC
after the WR bit is set.
After the erase sequence terminates, PGC must still be
held low for the time specified by parameter P10 to
allow high-voltage discharge of the memory array.
4-Bit Command
1
0
2
0
3
0
0
Programming Time
P9
 2010 Microchip Technology Inc.
4
P10
Data Payload
1
0
16-Bit
2
0
3
0