ST62T00CB6 STMicroelectronics, ST62T00CB6 Datasheet - Page 5

• Manufacturer Part Number: ST62T00CB6
• Description: IC MCU 8BIT OTP 1K 16-PDIP
• Manufacturer: STMicroelectronics
• Series: ST6r

Specifications of ST62T00CB6

• Core Processor: ST6
• Core Size: 8-Bit
• Speed: 8MHz
• Peripherals: LVD, POR, WDT
• Number Of I /o: 9
• Program Memory Size: 1KB (1K x 8)
• Program Memory Type: OTP
• Ram Size: 64 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 6 V
• Data Converters: A/D 4x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-DIP (0.300", 7.62mm)
• Controller Family/series: ST6
• No. Of I/o's: 9
• Ram Memory Size: 64Byte
• Cpu Speed: 8MHz
• No. Of Timers: 1
• Rohs Compliant: Yes
• Processor Series: ST62T0x
• Core: ST6
• Data Bus Width: 8 bit
• Data Ram Size: 64 B
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 9
• Number Of Timers: 2
• Operating Supply Voltage: 3 V to 6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: ST622XC-KIT/110, ST62GP-EMU2, ST62E2XC-EPB/110, ST62E6XC-EPB/US, STREALIZER-II
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit
• Cpu Family: ST6
• Device Core Size: 8b
• Frequency (max): 8MHz
• Total Internal Ram Size: 64Byte
• # I/os (max): 9
• Number Of Timers - General Purpose: 1
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 6V
• Operating Supply Voltage (min): 3V
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Through Hole
• Pin Count: 16
• Package Type: PDIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: In Transition
• Other names: 497-2093-5

1.2 PIN DESCRIPTIONS
V
these two pins. V
V
OSCin and OSCout. These pins are internally
connected to the on-chip oscillator circuit. A quartz
crystal, a ceramic resonator or an external clock
signal can be connected between these two pins.
The OSCin pin is the input pin, the OSCout pin is
the output pin.
RESET. The active-low RESET pin is used to re-
start the microcontroller. Internal pull-up is provid-
ed at this pin.
TEST/V
mal operation. If TEST pin is connected to a
+12.5V level during the reset phase, the EPROM
programming Mode is entered.
NMI. The NMI pin provides the capability for asyn-
chronous interruption, by applying an external non
maskable interrupt to the MCU. The NMI input is
falling edge sensitive. The user can select as op-
tion the availability of an on-chip pull-up at this pin.
PA1-PA3. These 3 lines are organized as one I/O
port (A). Each line may be configured under soft-
ware control as inputs with or without internal pull-
up resistors, interrupt generating inputs with pull-
up resistors, open-drain or push-pull outputs. PA1-
PA3 can also sink 20mA for direct LED driving.
DD
SS
is the ground connection.
and V
PP
. The TEST must be held at V
SS
. Power is supplied to the MCU via
DD
is the power connection and
SS
for nor-
PB0..PB1,PB3,PB5-PB7. These 6 lines are or-
ganized as one I/O port (B). Each line may be con-
figured under software control as inputs with or
without internal pull-up resistors, interrupt generat-
ing inputs with pull-up resistors, open-drain or
push-pull outputs. PB3,PB5..-PB7 can be used as
analog inputs for the A/D converter on the
ST62T00C, T01C and E01C.
Figure 2. ST62T03C,T00C, T01C, and E01C Pin
Configuration
*Analog input availability depend on device
V
Ain*/PB7
Ain*/PB6
PP
OSCout
RESET
OSCin
/TEST
ST62T00C/T01C ST62T03C/E01C
V
NMI
DD
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
PA3/20 mA Sink
PA2/20 mA Sink
PB3/Ain*
PB5/Ain*
PA1/20 mA Sink
PB0
PB1
V
SS
5/70
5