MC9S08LC36LH Freescale Semiconductor, MC9S08LC36LH Datasheet - Page 136

• Manufacturer Part Number: MC9S08LC36LH
• Description: IC MCU 36K FLASH 2K RAM 64-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08LC36LH

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LCD, LVD, POR, PWM, WDT
• Number Of I /o: 18
• Program Memory Size: 36KB (36K x 8)
• Program Memory Type: FLASH
• Ram Size: 2.5K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 2x12b
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 64-LQFP
• Processor Series: S08LC
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 2.5 KB
• Interface Type: I2C/SCI/SPI1/SPI2
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 18
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 2-ch x 12-bit
• For Use With: DEMO9S08LC60 - BOARD DEMO FOR 9S08LC60
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Chapter 9 Liquid Crystal Display Driver (S08LCDV1)
9.3.8
Read: anytime. The LCDCLR bit always reads zero.
Write: anytime.
136
BRATE[2:0]
BLKMODE
LCDDRMS
Reset
BLINK
LCDIF
Field
Field
2:0
7
3
7
3
W
R
LCDIF
LCD Command and Status Register (LCDCMD)
Blink Command — Starts or stops LCD module blinking.The blink command takes effect at the beginning of the
next LCD frame cycle.
0 Disables blinking.
1 Starts blinking at blinking frequency specified by
Blink Mode Select — Configures whether to blink either individual LCD segments or the entire LCD panel
depending on the state of the BLKMODE bit.BLINK must be enabled; if BLINK = 0, this bit has no effect.
0 Blink only individual LCD segments as specified by the LCDRAM register banks.
1 Blink all LCD segments regardless of contents of the LCDRAM register banks.
Blink Rate Configuration— Selects the frequency at which the LCD display blinks when the BLINK is asserted.
Equation 9-4
Equation 9-4
LCD module blink rate calculations are provided in 9.4.3.2/p.150.
LCD Interrupt Flag — LCDIF indicates that an interrupt condition has occurred. To clear the interrupt, read
LCDCMD register and then write a 1 to LCDIF.
0 interrupt condition has not occurred.
1 interrupt condition has occurred.
LCD Module Data Register Mode Select — The LCDRAM registers provide access to two different register
groups. Access to each register group is controlled by the state of the LCDDRMS bit.
0 Selects the LCDRAM registers to access registers that control the on/off state for LCD segments.
1 Selects the LCDRAM registers to access registers that control the blink enable/disable state for LCD
0
7
segments.
Unimplemented or Reserved
LCD module blink rate
shows how BRATE[2:0] bit field is used in the
provides an expression for the LCD waveform base clock
0
0
6
MC9S08LC60 Series Data Sheet: Technical Data, Rev. 4
Figure 9-9. LCD Command Register (LCDCMD)
Table 9-11. LCDBCTL Field Descriptions
Table 9-12. LCDCMD Field Descriptions
0
0
5
=
LCD waveform base clock
2
0
0
4
(5+ BRATE[2:0])
Description
Description
LCD
LCDDRMS
blink rate calculation (see
LCD
3
0
blink rate calculation.
0
0
2
Equation
LCDCLR
Freescale Semiconductor
0
0
1
9-4).
Eqn. 9-4
BLANK
0
0