ATTINY24A-MMH Atmel, ATTINY24A-MMH Datasheet - Page 108

• Manufacturer Part Number: ATTINY24A-MMH
• Description: MCU AVR 2K FLASH 20MHZ 20VQFN
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY24A-MMH

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 12
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-MLF®, QFN
• Processor Series: ATTINY2x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: SPI, USI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 20 Channel
• For Use With: ATSTK505 - ADAPTER KIT FOR 14PIN AVR MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

12.11.2
108
ATtiny24A/44A/84A
TCCR1B – Timer/Counter1 Control Register B
• Bits 1:0 – WGM1[1:0]: Waveform Generation Mode
Combined with the WGM1[3:2] bits found in the TCCR1B Register, these bits control the count-
ing sequence of the counter, the source for maximum (TOP) counter value, and what type of
waveform generation to be used, see
the Timer/Counter unit are: Normal mode (counter), Clear Timer on Compare match (CTC)
mode, and three types of Pulse Width Modulation (PWM) modes.
page
Table 12-5.
• Bit 7 – ICNC1: Input Capture Noise Canceler
Setting this bit (to one) activates the Input Capture Noise Canceler. When the noise canceler is
activated, the input from the Input Capture pin (ICP1) is filtered. The filter function requires four
successive equal valued samples of the ICP1 pin for changing its output. The Input Capture is
therefore delayed by four Oscillator cycles when the noise canceler is enabled.
• Bit 6 – ICES1: Input Capture Edge Select
This bit selects which edge on the Input Capture pin (ICP1) that is used to trigger a capture
event. When the ICES1 bit is written to zero, a falling (negative) edge is used as trigger, and
when the ICES1 bit is written to one, a rising (positive) edge will trigger the capture.
Bit
0x2E (0x4E)
Read/Write
Initial Value
Mode
10
11
12
13
14
15
0
1
2
3
4
5
6
7
8
9
94).
WGM1
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
[3:0]
Waveform Generation Modes
ICNC1
R/W
7
0
Mode of
Operation
Normal
PWM, Phase Correct, 8-bit
PWM, Phase Correct, 9-bit
PWM, Phase Correct, 10-bit
CTC (
Fast PWM, 8-bit
Fast PWM, 9-bit
Fast PWM, 10-bit
PWM, Phase & Freq. Correct
PWM, Phase & Freq. Correct
PWM, Phase Correct
PWM, Phase Correct
CTC (
(Reserved)
Fast PWM
Fast PWM
ICES1
R/W
Clear Timer on Compare
Clear Timer on Compare
6
0
R
5
–
0
Table 12-5 on page
WGM13
R/W
4
0
)
)
WGM12
R/W
3
0
TOP
0xFFFF
0x00FF
0x01FF
0x03FF
OCR1A
0x00FF
0x01FF
0x03FF
ICR1
OCR1A
ICR1
OCR1A
ICR1
–
ICR1
OCR1A
108. Modes of operation supported by
CS12
R/W
2
0
Update of
OCR1
Immediate
TOP
TOP
TOP
Immediate
TOP
TOP
TOP
BOTTOM
BOTTOM
TOP
TOP
Immediate
–
TOP
TOP
(“Modes of Operation” on
CS11
R/W
1
0
x
at
CS10
R/W
0
0
TOV1 Flag
Set on
MAX
BOTTOM
BOTTOM
BOTTOM
MAX
TOP
TOP
TOP
BOTTOM
BOTTOM
BOTTOM
BOTTOM
MAX
–
TOP
TOP
8183C–AVR–03/11
TCCR1B